Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Follow the instructions in Before You Begin. 2. Remove the base cover (see Removing the Base Cover). 3. Remove the rear caps (see Removing the Rear Caps). 4. Loosen the four captive screws that secure the central processor heat sink to the system board. 5. Lift the central processor heat sink off the computer. Replacing the Central Processor Heat Sink 1. Place the new thermal cooling pad on the central processor heat sink. 2. Place the central processor heat sink on the system board. CAUTION: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer). NOTICE: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not covered by your warranty. NOTICE: To help prevent damage to the system board, remove the main battery (see Before Working Inside Your Computer) before working inside the computer. 1 captive screws (4) 2 central processor heat sink NOTE: This procedure assumes that you have already removed the central processor heat sink and are ready to replace it. NOTE: If the central processor heat sink is replaced, the thermal cooling pad will be attached to the new central processor heat sink. 3. Tighten the four captive screws that secure the central processor heat sink to the system board. 4. Replace the rear caps (see Replacing the Rear Caps). 5. Replace the base cover (see Replacing the Base Cover). 6. Slide the battery into the battery bay until it clicks into place. Graphic Processor Heat Sink/Thermal Fan Removing the Graphic Processor Heat Sink/Thermal Fan 1. Follow the instructions in Before You Begin. 2. Remove the base cover (see Removing the Base Cover). 3. Remove the rear caps (see Removing the Rear Caps). 4. Remove the central processor heat sink (see Removing the Central Processor Heat Sink). 5. Loosen the two captive screws and remove the other two screws that secure the graphic processor heat sink/thermal fan to the system board. 6. Disconnect the thermal fan cable from the system board connector. 7. Lift the graphic processor heat sink/thermal fan off the computer. Replacing the Graphic Processor Heat Sink/Thermal Fan 1. Place the new thermal cooling pad on the graphic processor heat sink/thermal fan. 2. Place the graphic processor heat sink/thermal fan on the system board. NOTE: The graphic processor heat sink availability may depend on your system configuration. NOTE: The removal procedure for the thermal fan may differ according to your system configuration. 1 fan cable 2 graphic processor heat sink 3 thermal fan 4 screws (2) 5 captive screws (2) NOTE: This procedure assumes that you have already removed the graphic processor heat sink/thermal fan and are ready to replace it. NOTE: If the graphic processor heat sink is replaced, the thermal cooling pad will be attached to the new graphic processor heat sink. Use the thermal cooling pad provided in the kit on the central processor heat sink and graphic processor heat sink. 3. Tighten the two captive screws and replace the other two screws that secure the graphic processor heat sink to the system board. 4. Connect the thermal fan cable to the system board connector. 5. Replace the central processor heat sink (see Replacing the Central Processor Heat Sink) 6. Replace the rear caps (see Replacing the Rear Caps). 7. Replace the base cover (see Replacing the Base Cover). 8. Slide the battery into the battery bay until it clicks into place. Back to Contents Page Back to Contents Page Display Assembly Dell™ Studio XPS™ 1340 Service Manual Removing the Display Assembly Replacing the Display Assembly Removing the Display Assembly 1. Follow the instructions in Before You Begin. 2. Remove the palm rest (see Removing the Palm Rest). 3. Remove the optical drive (see Removing the Optical Drive). 4. Make note of the Mini-Card cable routing and carefully dislodge the Mini-Card antenna cables from their routing guides. 5. Pull the Mini-Card cables out through the system board so that they are clear of the computer base. 6. Make note of the display cable, power light cable, and camera cable routing. 7. Remove the display cable grounding screw that secures the display ground cable to the system board. CAUTION: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the compute...
Эта инструкция также подходит к моделям:Ноутбуки - Studio XPS M1340 (1.01 mb)