Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Back Panel Assembly The back panel module is the last module to be integrated to the APOLLO main system before the plastic housing is to be installed to the system. 1. On the I/O board, there are 6 D-SUB connectors with 2 bronze sticks on each side. Remove the 12 bronze sticks. 2. Insert the I/O board to the I/O bracket (2) and fix them together with the 12 bronze sticks. Fix them again with 2 screws on the other side. 3. Fix the complete I/O module to the metal back panel (1) five FMS 3*5 screws. 4. Connect one end of the 2 68-pin SCSI cables (Fig. 5-12 (4)) to the I/O board (3). Via the 2 SCSI cables, all the onboard I/O signals are converted to the I/O board for device cable connection. 5. Connect the other end of the two SCSI cables to the SCSI 1 and SCSI 2 connectors on the motherboard. 6. Fix the back panel module to the main system. 7. Fix a stand bracket at the bottom side of the chassis with 2 screws. User Manual version 2305 5.13. Stand Module Assembly The APOLLO system comes with a versatile stand composing of one big pedestal and one set of cable management covers. The following figure illustrates the steps to make up the APOLLO stand. 1. Refer to Fig. 5-13. Fix the two hinges to the hinge bracket (5). Then fix the unit to the metal base (1). Please note that the two hinges are different. The right side is used to fix the hinge knob. Note that there are two avocado-shape holes on the metal base. The two avocado holes are used to fix the stand to the table for special application. 2. Insert the stand bottom cover (4) to the hinge module and fix them together with four FMS 3*6 screws. 3. Fix the plastic upper cover (6) to the hinge bracket with 2 screws. 4. Insert the whole base unit to the base plastic cover (7) and fix them together with screws to make the complete unit a pedestal. 5. Insert the hinge knob (2) to the pedestal. ©.®yAK.O APOLLO °o®y.O.O HINGE (..) with LOCK HINGE (.k) APOLLO 120/150 Aa¶b...¤U»\ APOLLO 120/150 ¶i.¦©.®y Aa¶b¤a¬[ APOLLO 120/150 Aa¶b...¤W»\ FIGURE 5-13: APOLLO PEDESTAL ASSEMBLY 5-74 APOLLO 120/150 III User Manual version 2305 To assemble the stand module (Fig. 5-14 (1)) to the main system (2), simply tighten the two units together with 4 screws from the base. Then, install the two base back covers (4 & 5) to the unit as shown below. There is an additional knob in the accessory. If touchscreen is to be used with the system, it is suggested that the additional knob is to be assembled to the system to prevent the system from wobbling. By swiveling the knob and pulling the base up and down, the angle can be fixed at 45 to 900. °o®y.O«~ .DAe »P °o®y.O.. .DAe.O«~ APOLLO 120/150 ©.®y...¤W»\ APOLLO 120/150 ©.®y...¤U»\ FIGURE 5-14: APOLLO STAND TO MAIN SYSTEM ASSEMBLY 5-75 APOLLO 120/150 III User Manual version 2305 5-76 APOLLO 120/150 III User Manual version 2305 6. SYSTEM MOTHERBOARD & I/O BOARD The system controller used in the APOLLO III system is a special-design Celeron/Pentium® III multimedia motherboard. All the onboard signal is connected to an I/O board via 2 SCSI cables for external device connection. This chapter provides jumper definition and connector signal of the motherboard and the I/O board. 6-77 APOLLO 120/150 III User Manual version 2305 6.1. APOLLO III Motherboard This section provides background information and detail specification on the APOLLO 120/150 III system engine, PC 610. Sections include: . General Information . Features . Specification . Board placement & Dimension 6.1.1. General Information The PC 610 is an Intel Celeron/Pentium III (Socket 370) multimedia ATX motherboard with LCD/VGA controller, Ethernet 100/10, AC97 sound, and IDE flash disk. By integrating single chip, SiS630ST, the PC 610 provides a high performance/low cost desktop solution. Highly integrated, the PC 610 can adapt Intela Celeron (66/100MHz) and Pentium III (100/133MHz) CPU. Onboard features include four serial ports, one multi–mode Parallel ports, a floppy drive controller and a PS/2 keyboard PS/2 mouse interface. The built-in high speed PCI IDE controller supports both PIO and ATA 100 mode. Up to four IDE devices can be connected, including large hard disks, CD-ROM drives and other IDE devices. The full PC functionality coupled with its multi-I/Os stand ready to accommodate a wide range of PC peripherals. Compact in size and with its highly integrated multimedia and networking functions, the PC 610 is the most powerful PC engine to build any small footprint all-in-one PC system for integration into any space-constricted embedded applications. Fully configurable and with its modular design, the PC 610 is an ideal platform for any consumer computing applications where space is a premium. 6-78 APOLLO 120/150 III User Manual version 2305 6.1.2.Specifications PC 610: Multimedia Intel Celeron/Pentium III Motherboard with XGA, LCD, Dual display, Ethernet & Audio Interface u CPU: Intel Socket 370 · Intel Pentium III FCPGA 1GHz/133MHz · Intel Pentium III FCPGA 650-933/133MHz ·...
Эта инструкция также подходит к моделям:Ноутбуки - 120 III (2.04 mb)