10 When the message [You must reboot in order to enable the Backup function.] appears, remove the recovery CD-ROM, and press any key to restart the computer. The computer is restarted, then the backup process will begin. 11 When the message [[Backup] is complete] appears, press Ctrl + Alt + Del to restart the computer. Do not press Ctrl + Alt + Del until the message is displayed. CAUTION 12 After logging on to Windows, a message will appear advising that a new device has been installed and that the computer must be restarted to enable the settings. Select [Yes] to restart the computer. The [Boot] menu in the Setup Utility is set to start up from the DVD-ROM & CD-R/RW drive. Change this setting if necessary. The next time the backup or restore functions are executed, follow the procedure for [Backing Up and Restoring Data] ( below). NOTE 1 Turn the computer on, and press F2 while [Panasonic] boot screen is displayed. Backing Up and Restoring Data Before executing the backup function, execute a disk error check ( page 38). Do not interrupt the backup or restore functions before completion, for example by turning off the power or pressing Ctrl + Alt + Del , as this may prevent Windows from starting up, or may cause data to be lost so that the backup and restore functions cannot be executed. CAUTION The Setup Utility will start up. If a password has been set, enter the Supervisor Password or the User Password. 2 Select [Exit] menu, then select [Hard Disk Backup / Restore] and press Enter . At the confirmation message, select [Yes], and press Enter . 3 Select the operation to be executed from the menu. 1 to execute [1. [Backup]]. (When dividing the hard disk into two partitions, select the backup method at next screen.) Y1 Press 2 At the confirmation message, press 2 . The backup process will begin. 1 Press to execute [2. [Restore]]. (When data is backed up in two partitions, select the restore method at next screen.) Y2 At the confirmation message, press . The restore process will begin. Appendix 40 NOTE The time required to complete the backup or restore process differs depending on the data volume. Ctrl + Alt + Del Ctrl + Alt + Del • If the backup or restore process was interrupted before completion, for example if the power was turned off, execute the process again. • When a new device is installed and a message appears advising that the computer must be restarted to enable the settings, select [Yes] to restart the computer. To disable the hard disk backup function Perform the reinstallation procedure. All data in the backup area and the hard disk will be erased. Conduct steps 1-8 for [Reinstalling Software] ( page 34). Select [1] or [2] to execute the reinstallation at the screen for executing the reinstallation. • When [1] is selected, the hard disk backup function can be disabled. • When [2] is selected, the hard disk backup function can be disabled, but in this case, because the hard disk has been divided into partitions, the hard disk backup function cannot be re- enabled ( page 26). • When [3] is selected, the hard disk backup function cannot be disabled. CAUTION When the hard disk backup function has been enabled, the backed up data will not be erased even if a commercial data erasing utility or similar software is used to erase all data from user-accessible area. You can use the hard disk data erase utility included in this computer ( page 42) to erase all data on the hard disk, including backed up data. Use this hard disk data erase utility before disposing of or transferring ownership of this computer. Occasionally, the message [#1805 cannot write image file] will be displayed, and the backup function will be interrupted. If this error occurs, execute the backup function again. After this, if the backup function is completed properly, then there is no problem in the hard disk. If you select [3] in step 9 ( page 34) and execute reinstallation, the drive letter for the second partition (data partition) may be switched with that of the SD memory card. You can still use the drives after the letters have been switched, but you can also return the drive letters to their original state using the following procedures. (The following procedure assumes that before reinstallation, the second partition (data partition) was Drive D:, and the SD memory card was Drive E:) 1 123451234 Disable the drive letter for the second partition (data partition). Click [start] - [Control Panel] -[Performance and Maintenance] -[Administrative Tools] and double click [Computer Management]. Click [Disk Management] from [Storage]. Right click on the partition for which [E:] is displayed and click [Change Drive Letter and Paths...]. Click [Remove]. At the confirmation message, click [Yes]. 2 Change the SD memory card drive letter to [E:]. Use the SD drive letter change tool to ch...
)
