Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
(O’ Page 13) ^. (§) Enter the correct date, time and the time zone, then select [Next]. You can also complete these settings at a later time. (?) At the [Networking Settings], select [Typical settings], then select [Next]. (8) At the [Workgroup or Computer Domain], select [No, this computer is not on a network, or is on a network without a domain], then select [Next], The computer will restart. (?) Enter your administrator password and select ¡jj|. 8 Create Backup Disks for réinstallation (?) Prepare 2HD floppy disks and make sure they are not in the write-protected state, and insert the shutter-side headfirst. then set it. |Winciowsr2000l Select [Start] - [Programs] - [Panasonic] - [Create Backup Disk] and follow the onscreen instructions. IWindowstXRJ Select [start] - [All Programs] - [Panasonic] - [Create Backup Disk] and follow the onscreen instructions. When [You do not need to make “BACKUP DISK”] is displayed, there is no need to create a Backup Disk. (3) Place a label identifying the contents on each disk. • Name of created backup disk FIRSTAtD FD (When the display for creating the UPDATE FD is shown, create the disk by following the on-screen instructions.) Г mШ)- Store the floppy disks in a safe place. They will enable you to return your computer to close to the condition at the time of purchase should any problems occur. When creating backup disks, do not run any other application program. When creating backup disks and the message [Insufficient files to copy] is displayed, select [OK] and then contact Panasonic Technical Support. While the floppy disk drive indicator is on, do not remove the floppy disk, power off your computer or use the standby or hibernation function (Q3 “Standby/ Hibernation Functions”). Be sure to create the backup disk. If a backup disk is not created, it will be impossible to return the computer to its original state. In this case, contact Panasonic Technical Support. ( This concludes the first-time use operation guidelines. information for the CD-R/RW drive and DVD-ROM & CD-R/RVV drive> Before using the CD-R/RW drive or DVD-ROM & CD-R/RW drive for the first time, remove the protective sheet from the lens area. The protective sheet inside the drive delays the opening of the drive by about ten seconds. This delay is not a problem. 12 plnformationfor-Windows-XP^ • You can select Classic view for the Control Panel or select the Classic Start menu. You can also change the way a user logs on or off. The procedure in this manual uses the method or view of the Windows XP default setting (not Classic view or Classic Start menu etc.). • Resetting the password Windows XP has a function to reset a forgotten password. To use this function, you need to create a password reset disk beforehand following the steps below. 1 Select [start] - [Control Panel] - [User Accounts] and select the account you used to logon. 2 Select [Prevent a forgotten password] from the [Related Tasks] menu and create a password reset disk following the on-screen instructions. Store the password reset disk in a safe place. /note)--- Only the logon password for each account can be reset. ^ The password set in the Setup Utility cannot be reset._ • Depending on the Windows settings, installed applications, and drivers, menus and other displays may differ, or some functions (such as use of the password reset disk) may be inoperable. Check with your system administrator for details. 13 Getting Started Operation Starting Up/Shutting Down Starting Up Power Switch (!) Power Indicator® Open the display Slide the latch as shown and lift open the display. Turn your computer on Press the power switch and hold it for approximately one second until the power indicator turns on before releasing it. • After confirming that the power indicator has turned on, avoid the following until Windows has completed loading. • Connecting or disconnecting the AC adaptor. • Touching the power switch. • Performing any keyboard or touch pad (or external mouse) operations. • Closing the display. • Once the computer is powered off, you must wait at least ten seconds before powering it on again. • When the CPU temperature rises, the computer may not power on to prevent the CPU from overheating. Should this happen, allow the computer to cool down then switch the power on again. If the computer still does not power on, contact Panasonic Technical Support. _/ NOTE You may encounter the following situations when the computer is turned on at very low temperatures. These functions are designed to prevent hard disk drive malfunctions that may occur at low temperatures. • The message “Warming up the system” is displayed, and start-up takes longer than usual (a few minutes or more). In this case, wait for the computer to start up. • The power indicator will blink quickly (in green); in this case, the power does not turn on, or the computer does not resume from standby or hibernation mode. T...