Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
When the window display is restored by pressing Alt + Enter , the picture is displayed on both screens. When an a moving picture such as an MPEG file is being played with Media Player, the display destination cannot be switched using Fn + F3 The display destination cannot be switched while a moving picture such as an MPEG file is playing. Stop playing the moving picture before switching the display destination. Shutting Down Windows cannot be shut If a USB device is connected, try removing it. down or restartedIt may take one or two minutes to shutdown. Battery Indicator The red indicator lights. The battery level is very low (the charge is approx. 9% or less). Connect the AC adaptor. You can use the computer when the battery indicator light is orange. If you do not have an AC adaptor, save your data and power off your computer. After replacing the battery pack with a fully charged one, turn your computer on. The red indicator blinks Quickly save your data and power off your computer. Remove the battery pack and disconnect the AC adaptor, then connect them again. If the problem persists, contact Panasonic Technical Support. ( page 44) The battery pack or charging circuit may be defective. The green indicator blinks In high temperature mode, the battery is discharging to the level that corresponds to an 80%*1 charge for normal temperature mode. ( “Battery Power”) Do not remove the battery pack while the battery indicator is blinking green. *1 In high temperature mode, the level that corresponds to an 80% charge for normal temperature mode is displayed as [100%]. The battery indicator blinks green and orange alternately Warming up the system to prevent hard disk drive malfunctions at low temperature. Leave your computer as is. Once the allowable temperature range requirement is satisfied, your computer will start automatically. The orange indicator blinks Battery cannot be recharged temporarily because the internal temperature of the battery pack is outside of the acceptable temperature range for recharging. Once the allowable range requirement is satisfied, charging begins automatically. Your computer can be used normally in this state. The cursor cannot be controlled properly If you are using an external mouse, ensure that the external mouse has been connected correctly. Restart the computer by using the keyboard (Press , U , and select [Restart] with R ). If the computer does not respond to keyboard commands, read “No response” ( page 30). The cursor does not move in When the Microsoft® IntelliMouse™ Wheel mode or the original mode is set for the touch scrolling area of the touch pad, only scroll operations are possible for the right part or bottom part of the touch pad. pad In this case, cursor operations are possible by using the work surface excluding the right part or bottom part. When no mode is set, the entire surface of the touch pad can be used for cursor operations. Unable to input using the Has the Setup Utility been used to set [Touch Pad] to [Enable]? touch pad When external mouse drivers are installed (e.g., Intellimouse), the touch pad may not be used. Has the touch pad driver been properly installed? Unable to point correctly with the stylus included with the computer As a result of the physical characteristics of the touchscreen, sometimes the position of the stylus does not match the position of the cursor on the screen. This is not a malfunction. Perform [Calibration] ( page 13). Unable to input by touching the display Has the Setup Utility been used to set [Touchscreen] to [Enable]? When mouse drivers are installed (i.e. IntelliMouse), the touchscreen is unable to be used. Has the touchscreen driver been properly installed? Reference Manual The Reference Manual is not displayed Is Adobe Reader installed? If you have uninstalled Adobe Reader, install using the following procedures. 1 Select [start] - [Run], input [c:\util\reader\AdbeRdr60_enu_full.exe], then select [OK]. Install Adobe Reader by following the instructions on the screen. 2 Update Adobe Reader to its latest version. If your computer is connected to the Internet, start up Adobe Reader and select [Help] - [Update]. If your computer is not connected to the Internet, select [start] - [Run], input [c:\util\reader\Acro-Reader_6.0.2_Update.exe], then select [OK]. Fast User Switching function Some applications may not When switching to a different user with the Fast User Switching function, the following work properly problems may occur. • Some applications may not work properly. • Key combinations with the Fn key may not work. • It may not be possible to set the settings of the display. • A serial mouse may not work. •