Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
Follow the instructions on the screen to create a password. (D Select [Start] - [Turn Off Computer] - [Restart] to restart the computer. -\ Remember this password! If the password is forgotten, Windows cannot be operated. You can create a password reset disk beforehand (QjP below). 4_ When creating a new user account: • If you make mail settings, create password reset disks (Q13 below), or conduct other related operations before creating the user account, you will be unable to use any previous mail history or settings. • When you create the first new account, you can only select [Computer administrator]. Once a “Computer Administrator” account has been created, you can create additional limited user accounts. Note also that only the added user account will be displayed in the Welcome screen. The account for the administrator created during Windows setup will not be displayed. If you use the wireless LAN, be sure to refer to the Reference Manual’s “Wireless LAN”. ( This concludes the first-time use operation guidelines. ) Information for Windows XP • Depending on the Windows settings, installed applications, and drivers, menus and other displays may differ, or some functions (such as use of the password reset disk) may be inoperable. • You can select Classic view for the Control Panel or select the Classic Start menu. You can also change the way a user logs on or off. The procedure in this manual uses the method of the Windows XP default setting (not Classic Start menu etc.). • Resetting the password Windows XP has a function to reset a forgotten password. To use this function, you need to create a password reset disk beforehand following the steps below. 1 Selcct [Start] - [Control Panel] - [User Accounts], 2 Select [Prevent a forgotten password] from the [Related Tasks] menu of the account you have logged on to and create a password reset disk following the on-screen instructions. Store the password reset disk in a safe place. • Only the logon password for each account can be reset. The password set in the Setup Utility cannot be reset. 15 Getting Started Operation Starting Up/Shutting Down Starting Up Latch © Power Indicator © Power Switch (!) Open the display. (T) Pull the carrying handle forward. (2) Press the latch as illustrated. (3) Lift up the latch and open the display. Turn your computer on. Slide the power switch and hold it for approximately one second until the power indicator turns on before releasing it. Under the condition that both the AC adaptor and the port replicator are not connected, the power will not go on if the display is closed. While booting, avoid the following until the hard disk drive indicator (§|) has turned off. • Connecting or disconnecting the AC adaptor. • Touching the power switch. • Performing any keyboard, touch pad, touchscreen (only for models with touchscreen), or external mouse operations. • Closing the display. Once the computer is powered off, you must wait at least ten seconds before powering it on again. When the CPU temperature rises, the computer may not power on to prevent the CPU from overheating. Should this happen, allow the computer to cool down then switch the power on again. If the computer still does not power on, contact Panasonic Technical Support. When the power is turned on, sometimes the message “Warming up the system” is displayed or the battery indicator alternately blinks green and orange, and start-up takes longer than usual (a few minutes or more). This function is designed to prevent hard disk drive malfunctions that may occur at low temperatures. Please wait for the computer to start up. If [Enter Password] is displayed Enter your password*1 and press ( Enter ). (Q3 “Security Measures”) The correct password fi il Enter Password [ ] Will Start Three incorrect attempts or No password for about a minute [ 1 Will Not Start *1 Supervisor Password or User Password set in the Setup Utility (not (Power off) the Windows password). When an application or file that was previously displayed appears on your screen The standby or hibernation mode has been set (Q3 “Standby/Hibernation Functions”). 16 Log on to Windows. rnnmma After confirming that the hard disk drive indicator (g) has turned off, select the user and input the password, then select [£jj. Until the correct password is entered, the computer will not operate. —WWW After confirming that the hard disk drive indicator (g) has turned off, input the user name and password, then select [OK], Until the correct user name and password are entered, the computer will not operate. Select your application. You are able to start working on your computer. Xnote)-. • The power saving function is factory set, so if there is no input from a key, the touch pad, the touchscreen (only for models with touchscreen) or an external mouse (when one is connected) for a certain interval of time, the power to the LCD and hard disk may be turned off The L...