Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
. If you carry your computer without the latch lock in place, the battery pack may fall out. Before using the battery pack, carefully read “Precautions (Battery Pack)” ( page 7-8). CAUTION 4 Close the cover until it clicks into place. Latch Cover 2 3 4 Pen..........................1 Tether ...................... 1 Shoulder Strap ........1 ( page 12) ( page 10) 5 Lock the cover by sliding the latch to the left. 5 *1 If additional instructions are included with the computer, be sure to read them. It may be necessary to perform additional operations during the following procedures. 14Getting Started First-time Operation 5 Open the display. 1 Pull up latch A and release latch B. 2 Lift open the display. Slide the power switch and hold it for approximately one second until the power indicator turns on before releasing it. CAUTION Connect your computer to a power outlet. CAUTION Be sure the AC adaptor is connected until completing the first-time use operation. When using the computer for the first time, do not connect any peripheral device except the battery pack and AC adaptor to the computer. Handling the AC adaptor Do not twist or pull the AC power cord forcefully. Doing so may damage the connections. Use only the specified AC adaptor with your computer. Using an AC adaptor other than the one supplied might damage the battery and/or the computer. When the DC plug is not connected to the computer, disconnect the AC cord from your AC wall outlet. Problems such as sudden voltage drops may arise during periods of thunder and lightning. Since this could adversely affect your computer, an uninterruptible power source (UPS) is highly recommended unless the battery pack is installed. 4 6 Turn your computer on. Latch A Do not slide the power switch and hold it for more than four seconds; this will cause the power to be turned off forcibly. Do not slide the power switch repeatedly. Once the computer is powered off, you must wait at least ten seconds before powering it on again. Setup Windows. Moving the cursor or clicking buttons can be performed with the touch pad ( page 20). Latch B 2 1 Power Switch Power Indicator 1 At [Welcome to the Windows XP Setup Wizard], select [Next]. 2 After reading the agreement, select [I accept this agreement] or [I don’t accept this agreement], then select [Next]. NOTE If [I don’t accept this agreement] is selected, the Windows setup will be aborted. Do not press any keys or touch the touch pad until [Windows XP Professional Setup] is displayed. CAUTION 3 Select settings for your region, then select [Next]. 4 Enter your name and organization and then select [Next]. 7 DC-IN Jack DC IN 16 V 5 Enter your computer name and administrator password and then select [Next]. CAUTION Remember this password! If the password is forgotten, Windows cannot be operated. 5 Enter your computer name and administrator password and then select [Next]. CAUTION Remember this password! If the password is forgotten, Windows cannot be operated. 6 Enter the correct date, time and time zone, then select [Next]. NOTE It may take some time before the computer restarts and the screen of step 7 is displayed. Wait, and do not press any keys, or touch the touch pad, etc. The computer will restart. Enter your administrator password and select . 1 7 If the cursor can not be pointed correctly with the pen, perform [Calibration] in [start] - [Control Panel] - [Printers and Other Hardware] - [Tablet and Pen Settings]. When you perform the calibration, hold the pen at the same angle as you would when actually using it. Perform the calibration separately for [Landscape] and [Portrait]. NOTE If the message “Wait several minutes while the optimal configuration is being set. Do not shutdown the computer during this process.” is displayed, wait and do not press any keys, or touch the touchpad, etc. When Windows setup is completed, the following message will be displayed at the bottom right of the screen: “Your computer might be at risk.” Con- tinue to the next step. The message is generated by the [Security Center] function in [Control Panel], and does not indicate an error or malfunction. For more information about “Security Center”, page 26. NOTE When creating a new user account: • If you make mail settings, create password reset disks ( page 16), or conduct other related operations before creating the user account, you will be unable to use any previous mail history or settings. • When you create the first new account, you can only select [Computer administrator]. Once a “Computer Administrator” account has been created, you can cre- ate additional limited user accounts. Note also that only the added user account will be displayed in the Wel- come screen. The account for the administrator created during Windows setup will not be displayed. CAUTION Remember this password! If the password is forgotten, Windows cannot be operated. You can create a password reset disk beforehand. ( page 16) 5 Getting 8Create a new account. Select [sta...