Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
Please observe the local regulations regarding the disposal of EN packaging materials, exhausted batteries and old equipment. “Made for iPad” means that an electronic accessory has been designed to connect specifically to iPad, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPad may affect wireless performance. iPad is a trademark of Apple Inc., registered in the U.S. and other countries. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Philips is under license. Note ••The type plate is located on the back of the unit. EN 2 Your Wireless Microphone and Bluetooth® Speaker Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at If you contact Philips, you will be asked for the model and serial number of this apparatus. The model number and serial number are on the back of the apparatus. Write the numbers here: Model No. __________________________ Serial No. ___________________________ Introduction With the Philips wireless microphone and Bluetooth® speaker, you can: • dock your iPad onto the speaker to sing along with music from the app (The Voice: On Stage) through the wireless microphone. With the Bluetooth® speaker, you can: • play music from a Bluetooth® enabled device that supports A2DP (Advanced Audio Distribution Profile). • charge or play music from your iPad directly through the dock connector. • play music from other audio devices through the AUDIO-IN socket. What's in the box Check and identify the contents of your package: • Wireless microphone • Bluetooth® speaker • AC power cord • 3 X AAA batteries • Quick start guide • Safety sheet Overview of the unit Wireless microphone a Line out socket • (To use the microphone separately) connect to the MIC input socket of an existing Hi-Fi system. b Battery compartment c OFF/ON • Switch the microphone on or off. d Power indicator • Light up red when the wireless microphone is switched on. • Flash red when the battery level is low. Bluetooth® speaker dcba EN a • Turn the unit on/off. b Power/Bluetooth® indicator • Indicate the power/Bluetooth® status. c -/+ • Adjust volume. d • (Press) pair with a Bluetooth® enabled device that supports A2DP (Advanced Audio Distribution Profile). • (Press and hold) pair with the wireless microphone in case automatic pairing fails. e Dock for iPad f SOFTWARE UPGRADE (not for use by end users) g AUDIO-IN • Connect an external audio player through a 3.5mm audio input cable (not supplied). h AC MAINS~ • AC power socket. abcdefgh EN 3 Get started Always follow the instructions in this chapter in sequence. Connect power Caution ••Risk of product damage! Make sure that the power supply voltage corresponds to the voltage printed on the back of the unit. ••Risk of electric shock! When you unplug the AC power cord, always pull the plug from the socket. Never pull the cord. ••Before you connect the AC power cord, make sure that you have completed all the other connections. • Connect the AC power cord to • the AC MAINS~ socket on the back of the Bluetooth® speaker. • the wall power socket. Switch on the Bluetooth® speaker • Press on the top of the Bluetooth® speaker. »»The power indicator lights up white. • To switch the unit to standby mode, press on the top panel. • To switch the unit on from standby mode, press again. Tip ••If the speaker stays idle for more than 15 minutes, it switches to standby mode automatically. Install/replace microphone batteries Caution ••Risk of explosion! Keep batteries away from heat, sunshine, or fire. Never discard batteries in fire. ••Danger of explosion if batteries are incorrectly replaced. Replace only with the same or equivalent type. ••Batteries contain chemical substances, so they should be disposed of properly. 1 Open the battery compartment and take out the battery cartridge. 2 Insert 3 x AAA batteries (supplied) into the cartridge with correct polarity (+/-) as indicated. EN 3 Push back the battery cartridge, then close the battery compartment. Note ••If you are not going to use the microphone for a long time, remove the batteries. ••New batteries installed in the microphone support up to 30 hours of continuous use. ••When the power indicator flashes red, it indicates that the power level is low and you need to replace the batteries. EN 4 Play Sing along through the wireless microphone Note ••The effective operation range between the wireless microphone and Bluetooth® speaker is approximately 10 meters (30 feet). 1 Dock your iPad onto the Bluetooth® speaker. »»A prompt pops up on the iPad screen, asking you to install the relevant app. 2 Tap YES on the prompt to install the app (The Voice: On Stage) from Apple App Store. 3 After su...