Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
!CAUTION • Avoid accidental starting. Be sure switch is in the locked or OFF position before inserting battery pack, making any adjustments, changing accessories, or storing the tool. Carrying tools with your finger on the switch or inserting the battery pack into a tool with the switch ON invites accidents. • Wear safety glasses and ear protection during operation. • Remove any adjusting key or wrench before turning the power tool ON. An adjusting key or wrench left attached to a rotating part of the power tool may result in personal injury. • Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. • Always work in a well-ventilated area. Wear an OSHA-approved dust mask. • Hold tool by insulated gripping surface when performing an operation where the tool may contact hidden wiring. Contacting a “live” wire will make exposed metal parts of the tool “live” and shock the operator. • Keep hands away from rotating parts. !CAUTION When servicing tools, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury. Tool Use and Care: !WARNING • Do not use tool if switch does not turn it ON or OFF. Any tool that cannot be controlled with the switch is dangerous and must be repaired. • Ensure the switch is in the OFF position before inserting tool into power source. Doing so with the switch ON, may cause accidental starting. • Disconnect the plug from the powersource before making any adjustments, changing accessories, or storing. Such preventive safety measures reduce the risk of accidental starting. • Use clamps or another practical way to secure the workpiece to a stable platform. Never hold work in your hand, lap, or against other parts of your body when drilling. • This tool must NOT be modified or used for any application other than that for which it was designed. !CAUTION • Do not force the tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed. • Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edges are less likely to bind and are easier to control. • Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. • Use only accessories that are recommended by the manufacturer for your model. Accessories suitable for one tool may create a risk of injury when used on another tool. • Some wood contains preservatives which can be toxic. Take extra care to prevent inhalation and skin contact when working with these materials. Request and follow all safety information available from your material supplier. • Store tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users. Reciprocating Saw Handling: • Hold tool by insulated gripping surface when performing an operation where the tool may contact hidden wiring. Contacting a “live” wire will make exposed metal parts of the tool “live” and shock the operator. !PRECAUCION El servicio de la herramienta debe ser realizado solo por personal de reparaciones calificado. El servicio o mantenimiento realizado por personas no calificadas puede provocar riesgo de lesiones. Minimum Wire Size (AWG) of Extension Cord for Length of Cord in Feet 25 50 100 150 AWG Size of Cord 18 18 18 16 2 DG420700CK Mantenimiento (continuacion) carbon por una pieza identica cuando se gaste o este cerca del limite. Ademas, mantenga siempre limpias las escobillas de carbon y asegurese de que se deslicen con libertad en el soporte de escobillas. Servicio tecnico Para obtener informacion con relacion al funcionamiento o reparacion de este producto, sirvase llamar al 1-800-424-8936. Para Ordenar Repuestos o Asistencia Tecnica, Sirvase Llamar al Distribuidor Mas Cercano a Su Domicilio Numero del DescripcionRepuesto Juego de hoja de sierra, tres hojas DG026200AV Llave Allen de 4 mm DG026300AV Sirvase darnos la siguiente informacion: - Numero del modelo - Codigo impreso - Descripcion y numero del repuesto segun la lista de repuestos Dirija toda la correspondencia a: Campbell Hausfeld Attn: Customer Service 100 Production Drive Harrison, OH 45030 U.S.A. Notas 15 Sp Manual de Instrucciones DG420700CK !WARNING General Safety 4. Support large panels to minimize 6. Operate the contrary to the above the risk of blade pinching and steps to disassemble blade. Information (cont’d.) Asegurese de que la hoja no toque la KICKBACK. Large panels tend to sag pieza de trabajo hasta que la sierra under their own weight. Supports Operation • Do not start the saw with the blade alcance la maxima velocidad definida m...