Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Item # 123008 READ ALL INSTRUCTIONS BEFORE OPERATING SAVE THESE INSTRUCTIONS Thank you for purchasing your Northern IndustrialTM Air Compressor. Before attempting to operate your new tool please read these instructions thoroughly. You will need these instructions for the safety warnings, precautions, assembly, operation and maintenance procedures. WARNING: The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions or situations that could occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. TABLE OF CONTENTS Description Page # Specifications .......................................1 Safety rules ..........................................2 Know Your Tool.....................................3 Getting Started .....................................3 Assembly..............................................3 Operation..............................................4 Maintenance.........................................6 Troubleshooting....................................7 Parts List and Diagram.........................8 SPECIFICATIONS Motor...................................120V ~ 60Hz HP.......................................2 Weight.................................59.5 lbs Tank Capacity .....................4 Gallon Air Pressure........................115 psi CFM ....................................5.5 CFM@40 PSI ............................................3.5 CFM@90 PSI CSA Listed.......................... 1 SAFETY RULES 1. Know your tool. Read this manual carefully. Learn the tool’s applications and limitations, as well as specific potential hazards peculiar to it. 2. Ground all tools. If the tool is equipped with three- pin plug, it should be plugged into a three-pin electrical socket. Never remove the ground pin. 3. Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is grounded. 4. Do not expose tool to moisture. Don’t use this tool in damp or wet locations. Keep out of rain. 5. Do not abuse cord. Never use the cord to carry tools or pull the plug from an outlet. Keep cord away from heat, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock. 6. Remove adjusting keys or wrenches before turning the tool on. A wrench or key that is left attached to a moving part of the tool may result in personal injury. 7. Keep work area clean and well lit. Cluttered or dark work areas invite accidents. 8. Keep children away. All children should be kept away from the work area. Never let a child handle a tool without strict adult supervision. 9. Do not operate this tool if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not attempt to operate. 10. Use safety equipment. Eye protection should be worn at all times when operating this tool. Use ANSI approved safety glasses. Everyday eyeglasses are NOT safety glasses. Dust mask, non-skid safety shoes, hard hat, or hearing protection should be used in appropriate conditions. 11. Wear proper apparel. Loose clothing, gloves, neckties, rings, bracelets, or other jewelry may present a potential hazard when operating this tool. Please keep all apparel clear of the tool. 12. Don’t overreach. Keep proper footing and balance at all times when operating this tool. 13. Always disconnect the tool from power source before making any adjustments, storing, servicing, or changing accessories. Such preventative safety measures reduce the risk of starting the tool accidentally. 14. Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it was designed. 15. Do not use the tool if the switch does not turn it on and off. Any tool that cannot be controlled with the switch is dangerous and must be repaired. 16. Check for damage. Check your tool regularly. If part of the tool is damaged it should be carefully inspected to make sure that it can perform its intended function correctly. If in doubt, the part should be repaired. Refer all servicing to a qualified technician. Consult your dealer for advice. 17. Keep away from flammables. Do not attempt to operate this tool near flammable materials or combustibles. Failure to comply may cause serious injury or death. 18. Store idle tools out of the reach of children and untrained persons. Tools may be dangerous in the hands of untrained users. 19. Maintain tools with care. Keep tools sharp and clean. Properly maintained tools, with sharp cutting edges, are less likely to bind and are easier to control. 20. Never exceed the pressure rating of any component in system. 21. Protect material and air lines from damage or puncture. Keep hose a...