Оценок - 5, средний балл: 3.6
(
)
)
|
Фрагмент инструкции
2—Bryant Non-Programmable Thermostat fiers offer the added benefits of having the air continuously cleaned year-round, and humidified during the winter season. • Ventilation A system equipped with a heat or energy recovery ventilator offers the advantage of exhausting stale air from the home and allowing fresh air in from the outdoors while minimizing heat loss. • Zoning Your system may also be equipped with a zoning system which allows individual control over the temperatures of separate areas of your home. • Check Condensate Drain Your heat pump system will remove humidity from your home during the cooling season. After a few minutes of operation, you should be able to see water trickle from the condensate drain of the cooling coil. Check this occasionally to be sure the drain system is not clogged. Of course, don’t expect to see much drainage if you live in a very dry environment. RESET FILTER BUTTON HOLD BUTTON MAINTAINS SET TIME BUTTON FAN BUTTON CHOOSES BETWEEN ON OR AUTO FAN OPERATION LCD READOUT DISPLAYS CURRENT ROOM TEMPERATURE, DESIRED ROOM TEMPERATURE OR OUTDOOR TEMPERATURE, UNIT MODE SETTING, FAN MODE SETTING, AND TIME OF DAY MODE BUTTON SELECTS BETWEEN OFF, HEAT, COOL, AUTO, AND EMERGENCY HEAT OPERATION PROGRAM BUTTONS FOR PROGRAMMING HEATING/COOLING CYCLES Programmable Thermostat HOLDRESET FILTERSET TIME/TEMP FANENDCHANGE DAY MODEPROGRAMCOPY PREVIOUS DAY • Heated Air Temperature During the heating cycle, air from your registers may seem cooler than you might first expect. This is because the air is being delivered at a higher velocity and a more constant flow than air supplied by a conventional furnace. Also, your heat pump supplies air at 90 to 105°F instead of in sudden bursts of hot air as with a conventional furnace. The air may feel cool because it is slightly less than your body temperature. However, it is sufficiently warm to keep you comfortable. UP AND DOWN BUTTONS INCREASE OR DECREASE THE DESIRED TEMPERATURE SETTINGS RESTARTS THE TIMER THE CURRENT TEMPERATURE THAT CALCULATES AND OVERRIDES PROGRAMMED THE NEXT AIR FILTER TEMPERATURE CHANGES CHANGE OR CLEANING UNTIL RESET Fig. 3—Bryant Programmable Thermostat 3 • Don’t Worry About Ice On Your Unit Ice or frost will tend to form on the outdoor coil during the winter heating operation. Your heat pump is designed to automatically melt the ice. When in this defrost cycle, it is normal for steam or fog to rise from the outdoor unit. Do not be alarmed! • When Not To Use Your Unit Do not operate your unit in cooling mode when outdoor temperatures are below 55°F. Do not operate your unit in heating mode when outdoor temperatures are above 66°F. OPERATING YOUR HEAT PUMP The operation of your heat pump system is controlled by the indoor thermostat. You simply adjust the thermostat and it maintains the indoor temperature at the level you select. Most thermostats for heat pump systems have three controls: a temperature control selector, a FAN control, and a SYSTEM or MODE control. The temperature control selector is a dial, lever, or set of buttons that allows you to establish the degree of temperature that you wish to maintain for your personal comfort. Some thermostats possess two temperature control selectors: one for setting the temperature desired during the cooling cycle, and one to set the heating operation temperature. The FAN control offers two options for controlling the indoor blower: AUTO and ON. When set to AUTO, the blower runs only during the time the heat pump is operating. When set to ON, the blower will run continuously. Typically, the SYSTEM or MODE control on your thermostat offers the following selections: COOL, OFF, HEAT, AUTO, and EMERGENCY HEAT. Some thermostats may have a separate switch for EMERGENCY HEAT. The heat pump will not operate when the SYSTEM or MODE control is set to OFF. With the SYSTEM or MODE control set to COOL, your heat pump will operate in cooling mode when the indoor temperature rises above the level that you wish to maintain. With the SYSTEM or MODE control set to HEAT, your heat pump will provide warmth whenever the indoor temperature falls below the level that you have selected. The AUTO selection found on some thermostats provides for automatic changeover between cooling and heating cycles. With the SYSTEM or MODE control set to AUTO, cooling mode is activated when the indoor temperature rises above the thermostat cooling temperature setting, or heating mode is activated when the indoor temperature drops below the thermostat setting for the heating cycle. Depending on your typical winter heating needs, your home comfort system may include a supplementary heating source. The EMERGENCY HEAT setting (EHEAT) provides for convenient selection between the two heating appliances. Your heat pump will operate when the SYSTEM or MODE control is set to HEAT. With the SYSTEM or MODE control set to EHEAT, the heat pump will turn off and the supplementary heat source will be activated. NOTE: Your 2-speed heat pump...
Эта инструкция также подходит к моделям:Насосное оборудование - Puron Refrigerant Single Speed (157.12 kb)