Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
(Most air tools will have an air requirement stated in terms of a specific CFM at a specific pressure.) 2. The compressor should put out a higher CFM than the tool requires. If you are connecting multiple tools that will be used simultaneously, then the CFM for each tool should be added together and compared to the compressor output value. 3. Connect the tool, using a good quality air line with an adequate length to reach from the compressor to the point of use. Note—Quick-connect couplers, shown in Figure 10, are a good option for a fast and sure connection of tools and air hoses. Figure 10. Quick connect couplers These couplers are included with the air compressor. Make certain the air hose will not be placed in a position where it can become constricted or cut by a sharp object. Note—Running over a hose with heavy vehicles may not cause an immediate leak, but it will shorten the life of the hose. Consideration should also be given to the type of usage. A nailer or staple gun uses air in short bursts and it is easier for the compressor to maintain pressure. A paint sprayer or grinder tends to use a more continuous stream of air as these tools are run for longer time periods. It is always better to oversize a compressor to allow for variation in the type of usage and the number of tools to be powered. Air tools being operated with insufficient air volume will not perform their function satisfactorily. Always disconnect air hose from tools whenever not in use or while servicing! During maintenance, a tool connected to air may operate accidentally, causing serious per- sonal injury! The Model H4517/H4518 Air Compressors are specifically designed for air tool operation. DO NOT MODIFY OR USE THIS MACHINE FOR ANY OTHER PUR- POSE. Modifications or improper use of this tool will void the warran- ty. If you are confused about any aspect of this machine, DO NOT use it until you have answered all your questions. Serious personal injury may occur. Model H4517/H4518 Air Compressors -11 MAINTENANCE Each Use Regular periodic maintenance on your air compressor will ensure its optimum performance. Make a habit of inspecting your compressor each time you use it. Check the following items: 1. Check Oil Level! Use the sight gauge on the bottom of the crankcase to make sure the oil level is at the proper height. 2. Drain tanks daily of any condensation by opening the drain valve on the bottom of the tank and leave open until the next time it is used. Depending upon the amount of use and the surrounding humidity, a certain amount of condensed water may accumulate in the tanks. For longevity of the compressor seals and the air tools you connect, it is best to drain water from the tanks. The tanks are best drained if the drain valve is open when the system is pressurized. Always wear safety glasses and use extreme caution when working around compressed air. The force of the air stream can cause small bits of debris to become airborne and cause potential injury to the eyes or other parts of the body. Never let the full force of the air stream come in direct contact with the skin as it can cause abrasions or bruising, penetration of skin and could even lead to death! The air compressor will cycle automatically when it is on. When performing any type of maintenance always make sure the AUTO/OFF lever is in the OFF position the unit is unplugged and bleed out all tank pressure. 3. Clean off the cylinder head cooling fins. Dirt interferes with heat transfer. 4. Check for worn or damaged cords and plugs. 5. Check for any other condition that could hamper the safe operation of this machine. 6. Check the safety drain valve to make sure it is working properly. Always drain the air from the tank before performing any maintenance or transporting your air compressor. Damage to the air compressor while under pressure could cause bursting or explosion and injury or property damage could occur. -12- Model H4517/H4518 Air Compressors After First 50 Hours of Use After the first 50 working hours or 30 days, whichever comes first, the following maintenance should be done. 1. Replace the oil in the crankcase with compressor oil or use ISO 100 or SAE 30W viscosity, non detergent type oil. 2. Check to make sure that all the fittings are tight. 3. Remove the air filter foam element shown in Figure 11 and rinse it out with water. Allow it to dry and reinstall. Figure 11. Air filter foam element 4. Blow out any dirt that has accumulated between the cylinder cooling fans. Weekly If the compressor is used on a daily basis, perform the following checks each week. 1. Rinse the air filter foam element in water. 2. Check for loose bolts or fittings. 3. Clean off all foreign material from cylinder head, motor, fan, air lines, exhaust pipe, couplers and frame. 4. Check air lines and connectors to make sure they are in good condition. Model H4517/H4518 Air Compressors -13 Every 300 Hours After every 300 hours or 3 months of regular operation, perform the followi...
Эта инструкция также подходит к моделям:Насосное оборудование - H4517 (1.06 mb)