Оценок - 2, средний балл: 5 ( )

Производитель: John Deere Размер: 3.11 mb Название файла: Язык инструкции:

Do NOT brush dirt. Brushing will force dirt into element fibers. Replace paper element after 300 hours, or if excessively dirty. 6. Install air cleaner in reverse order as removed. NOTE: SEE PICTURES ON NEXT PAGE -40°F-22°F-4°F14°F32°F50°F68°F86°F104°F122°F50°C40°C30°C20°C10°C0°C-10°C-20°C-30°C-40°CSAE 10W-40SAE 10W-30SAE 5W-30 Service HONDA SUBARU CLEANING AND GAPPING SPARK PLUG 1. Remove and inspect spark plug. If porcelain is cracked or electrodes are pitted, install a new spark plug. IMPORTANT: DO NOT CLEAN SPARK PLUG IN A MACHINE USING ABRASIVES. 2. If spark plug is in good condition, clean plug by scraping or using a wire brush. Wash with a commercial solvent. 3. Use a round wire-type feeler gauge to check for a gap of 0.70 to 0.80 mm (0.028 to 0.031 inches.) 4. Carefully bend outer electrode to adjust gap. PIC156R•121902R0 PIC93•102299R0 A A PIC94R-121902R0 B PIC94-102299R0 B C C PIC95-102299R0 PIC95R-121902R0 D PIC99-102299R0 5. Install spark plug. Reinstalling used plug: Tighten 1/8 - 1/4 turn after spark plug seats to compress washer. Installing new plug: Use NGK BPR6ES ADJUSTING RPM 1. Start engine. Allow it to warm to normal operating temperature. 2. Move throttle lever to its minimum position. 3. With engine idling, turn throttle stop screw (A) to obtain standard idle speed. NOTE: Standard idle speed is 1250 - 1550 RPM. NOTE: Idle should be serviced every 300 hours by an authorized dealer. Operator should adjust only if mechanically proficient and using proper tools. CLEANING SEDIMENT CUP CAUTION: CLEAN SEDIMENT CUP IN A WELL VENTILATED AREA, AWAY FROM SPARKS OR FLAME, INCLUDING ANY APPLIANCE WITH A PILOT LIGHT. DO NOT USE GASOLINE OR A LOW FLASH-POINT SOLVENT TO CLEAN THE FUEL VALVE. A FIRE OR EXPLOSION COULD RESULT. NOTE:Clean sediment cup after every 100 hours of use. 1. Turn fuel valve (A) to left as illustrated to shut off the fuel flow. 2. Remove cap screw (B) with a 10mm wrench. Remove sediment cup (C) and o-ring. 3. Remove any sediment or other foreign matter and wash in nonflammable or high flash point solvent. Dry thoroughly. 4. Install o-ring and sediment cup with cap screw. 5. Turn fuel valve right to “ON” position and check for fuel leaks. Service A A C B Solutions Solution 1: Remove debris in impeller. (Do not remove impeller) Solution 2: Check suction hose. Most cases of lack of priming or low water flow are caused by air leakage on the suction side of the pump. Suction test: a. Remove suction hose b. Start engine with water inside the pump. c. Press the palm of your hand to cover the suction inlet, hold and wait 30 seconds. If you feel suction on your palm, the pump is working fine. Check suction hose and connections. d. Check if rubber seal is installed. Note: In case of water leakage between engine and pump, usually the cause is damaged mechanical seal. Please ask shop for assistance and replace mechanical seal. Accessories 2" DISCHARGE SUCTION KIT: 70-0524 Includes: • 20' 2" Suction hose (15-0293) • 50' 2" Discharge hose (15-0295) • 2" Suction strainer (19-0628) 3" DISCHARGE SUCTION KIT: 70-0525 Includes: • 20' 3" Suction hose (15-0294) • 50' 3" Discharge hose (15-0296) • 3" Suction strainer (19-0629) Warranty John Deere warrants all parts, (except those referred to below), of your new pump to be free from defects in materials and workmanship during the following periods: For Two (2) Years from the date of original purchase. Defective parts not subject to normal wear and tear will be repaired or replaced at our option during the warranty period. In any event, reimbursement is limited to the purchase price paid. Exclusions 1. Engine/Motor are covered under separate warranty by its respective manufacturer and is subject to the terms set forth therein. 2. Normal wear parts: Mechanical Seal 3. This warranty does not cover parts damaged due to normal wear, misapplication, misuse, operation at other than recommended . Failure to follow recommended operating and maintenance procedures also voids warranty. 4. The use of other than genuine manufacturer repair parts will void warranty. 5. Parts returned, prepaid to our factory or to an Authorized John Deere Service Center will be inspected and replaced free of charge if found to be defective and subject to warranty. There are no warranties which extend beyond the description of the face hereof. Under no circumstances shall the manufacturer bear any responsibility for loss of use of the unit, loss of time or rental, inconvenience, commercial loss or consequential damages. For Service or Warranty Consideration, contact Mi-T-M® Corporation, 8650 Enterprise Drive, Peosta, IA 52068 563-556-7484 / 800-553-9053 / Fax 563-556-1235 Monday - Friday 8:00 a.m. - 5:00 p.m. CST Semi-Trash Pump Operator's Manual 19 Introduction Felicitations de l'achat de votre nouveau la cle a outil! Vous pouvez etre assure que votre nouveau la outil a ete construit avec le plus haut niveau de precision et de fiabilite. Chaque composant a ete rigoureusement teste pa...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: