Оценок - , средний балл:
(
)
)
Производитель: Aquacal
Размер: 2.64 mb
Название файла:
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
Owners: if your installation includes an external controller, contact your installing dealer, or the external controller manufacturer, for external controller operating instructions. These instructions are for quick-starting in the HEATING mode... Owners of Heat-Cool units, in order to utilize all features of their heater, will certainly want to also refer to: Owner Level Programming, beginning on page-14 of this manual. 1. Verify Electrical Power is Present at Heater: A. Ensure that the unit has electrical power connected; the heater controller display should be illuminated. B. If the display is blank, be certain the electrical breaker, and heater disconnect, are switched to “ON.” C. For now, leave the water circulation pump OFF. 2. Set the Heater Controls (Refer to Control Panel Layout, Pg-12): OWNER- If heater is connected to a Call-Flex controller, also see “Selecting Call-Flex Pump Options,” located on page-17 of this manual. INSTALLER- Is heater connected to an external controller? If so, see external controller information located on pages 41 and 44 of this manual. A. The user/owner settings can be made without water flowing. Once the heater has electrical power connected, with water not flowing, the display should read FLO. B. Press the MODE button until the HEAT (HEA) indication displays. This action will enable the remaining programming keys. C. Using the POOL / SPA selector key, select the POOL mode. An illuminated POOL indicator light, located on the left side of the display, will confirm the POOL control has been selected. If heating only a spa, using the DOWN arrow key, lower the POOL temperature until OFF is displayed; then proceed to Step-“E.” D. Use the UP / DOWN arrow keys to set the desired water temperature for the POOL water. E. If the heat pump will be used to heat a spa, use the POOL/SPA selector key to select SPA, then use the UP / DOWN arrow keys to set the desired water temperature for the SPA. An illuminated SPA indicator light, located on the left side of the display, will confirm the SPA control has been selected. If heating only a POOL, using the DOWN arrow key, lower the SPA temperature until OFF is displayed. F. The heat pump controls are now set to maintain the desired water temperature for the POOL and/or SPA. (Quick-Start & Stop Continued Next Page) HEATING-QUICK START & STOP (continued): 3. To Begin Heating: A. Verify MODE is set to: HEAT (HEA); then, depending on which body of water is to be heated, use the POOL / SPA selector key to select POOL or SPA. B. Position water valves to flow water from the pool or spa, through the heater, and back to the pool or spa. C. Start the water pump; the fan will start, and after 4-minute time delay the unit will begin heating. The selected body of water will be brought to temperature and maintained per the setting determined previously in: “Set the Heater Controls.” D. In operation, whenever the actual (displayed) water temperature falls below the desired set point, after an initial time delay of 4-minutes, the unit will begin heating. NOTE: THE HEATER CONTROLLER INCORPORATES AN ANTI-SHORT CYCLE TIME DELAY. SHOULD OPERATION BE INTERRUPTED, COMPRESSOR RESTART WILL BE DELAYED BY APPROXIMATELY 4-MINUTES. 4. Program Filter Pump Run Time: Most pool/spa systems utilize a timer or multifunction controller to manage filter pump run times. If your system incorporates such a device, follow the instructions below: A. It will be necessary to allow the filter pump to run continuously until the water has reached the desired temperature. If a timer controls the pool filter pump, it will be necessary to override the timer to allow 24-hr. operation. B. Once the desired temperature has been obtained (1-4 days), reset the pump control device. Colder months require longer running times–generally eight to twelve hours/day. C. A heat pump can only operate when the filter pump is running. Therefore, it may be necessary–during cooler weather–to extend the water pump’s hours of daily operation. The increased run time is necessary in order to keep up with increased, weather-related heat losses. 5. Continuous Usage and Water Around Heater: Condensation... After the heat pump has been operating for some time, water may be observed surrounding the heater. The moisture seen is condensation produced as a normal by-product of transferring heat from the air into the pool or spa water. Quantities of 6-8 gallons of water produced per hour are common if the air humidity is high. Conversely, a low humidity condition may result in no condensation being produced. (If water around unit seems excessive, to troubleshoot, see page-26, “Water Coming from the Heat Pump.”) 6. To Stop the Heat Pump: A. Select: OFF via the MODE selector. This method of shut down preserves the controller settings; B. An interruption of water flow–such as when a pump timer is in control–will also halt heat pump operation. (End...Quick-Start & Stop) 12 HEATER CONTROLS Control Panel Layout (APPEARANCE ...
Эта инструкция также подходит к моделям:Насосное оборудование - 111 (2.64 mb)
Насосное оборудование - 101 (2.64 mb)
Насосное оборудование - 110 (2.64 mb)
Насосное оборудование - 120 (2.64 mb)