Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
The use of replacement parts which are not of equivalent quality may damage the engine. Maintenance Schedule \ REGULAR SERVICE PERIOD ITEM perform at every indicated monttTor^ operating hour interval, which > ever comes first. \ Each use First month or 20 Hrs. Every 3 months or 50 Hrs. Every 6 months or 100 Hrs. Every year or 300 Hrs. Engine oil Inspection o Change o O Air cleaner element Inspection o Cleaning °(1> Spark plug maintenance o Tappet clearance adjustment 0(2) Combustion chamber cleaning 0(2) Fuel tank cleaning 42» Spark arrester Clean every 100 operating hours. Fual line Replace every 3 years. Impeller inspection <-12) Friction disc inspection 0(2) Casing cover inspection 0(2) Inlet valve inspection 0(2) NOTE (1): Service more frequently when used In dusty areas. (2): These items should bG serviced by an authorized Honda dealer, unless the owner has the proper tools and is mechanically proficient. See the Honda Shop Manual. 11 1. Changing oil Drain the oil while the engine is still warm to assure rapid and complete draining. 1. Remove the oil filler cap, and drain the oil. 2. Reinstall the drain plug and tighten securely. 3. Refill with the recommended oil (see page 4) and check the ieve!. OIL CAPACITY: 0.6? 10.63 US qt) CAUTION: Used motor oil may cause skin cancer if repeatedly left in contact with the skin for prolonged periods. Although this is unlikely unless you handle used oil on a daily basis, it is still advisable to thoroughly wash your hands with soap and water as soon as possible after handling used oil. NOTE: Please dispose of used motor oil in a manner that is compatible with the environment. Wc suggest you take it in a sealed container to your local service station for reclamantion. Do not throw it in the trash or pour it on the ground. 12 2. Air cleaner service A dirty air cleaner will restrict air flow to the carburetor. To prevent carburetor malfunction, service the air cleaner regularly. Service more frequently when operating the pump in extremely dusty areas. Never use gasoline or low flash point solvents for cleaning the air cleaner element. A fire or explosion could result. CAUTION: Never run the pump without the air cleaner. Rapid engine wear may result. 1. Unscrew the wing nut, remove the air cleaner cover and remove the element. 2. Wash the element in a non-flammable or high flash point solvent and dry it thoroughly. 3. Soak the element in clean engine oil and squeeze out the excess oil. 4. Reinstall the air cleaner element and the cover. A1R CLEANER COVER AIR CLEANER ELEMENT 13 3. Spark plug service Recommended spark plug: BPR6ES (NGK) W20EPR-U (ND) To ensure proper engine operation, the spark plug must be properly gapped and free of deposits. 1. Remove the spark plug. FTCTlin If the engine has been running, the muffler will be very hot. Be careful not to touch the muffler. 2. Visually inspect the spark plug. Discard it if the insulator is cracked or chipped. Clean the spark plug with a wire brush if it is to be reused. 3. Measure the plug gap with a feeler gauge. The gap should be 0.6—0.7 mm (0.024-0.028 tn}. Correct as necessary by bending the side electrode. 14 4. Attach the plug washer. Thread the plug in by hand to prevent cross-th reading. 5. Tighten a new spark plug 1/2 turn with the wrench to compress the washer. If you are reusing a plug, it should only take 1/8—1/4 turn after the plug seats. CAUTION: The spark plug must be securely tightened. An improperly tightened plug can become very hot and possibly damage the engine. Never use a spark plug with an improper heat range. 15 4. Adjusting carburetor screws 1. Start the engine and warm up it to the normal operating temperature 2. With the engine idling, turn the pilot screw in or out to the setting that produces the highest idle rpm. The correct setting wil! usually be approximately 3 turns out for the WA20X, and 1-5/8 turns out for the WA30X from the fully closed position. 3. After the pilot screw is correctly adjusted, turn the throttle stop screw to obtain the standard idle speed. Standard idle speed: 1,400± 150 rpm 16 8. TRANSPORTING/STORAGE WARNING When transporting the pump, turn the fuel valve OFF and keep the pump level to prevent fuel spillage. Fuel vapor or spilled fuel may ignite. Before storing the pump for an extended period; 1. Be sure the storage area is free of excessive humidity and dust. 2. Clean the pump interior..... Sediment will settle in the pump if it has been used in muddy or sandy water, or water containing heavy debris. Pump clean water through the pump before shutting down or impeller may be damaged when restarting. 3. Drain the fuel...... a. With the fuel valve OFF, remove the carburetor float bowl and drain the carburetor. Drain the gasoline into the suitable container. b. Turn the fuel valve ON and drain the gasoline in the fuel tank into the sui...
Эта инструкция также подходит к моделям:Насосное оборудование - WA20X (550.14 kb)