Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
Check oil level frequently at higher temperatures. Synthetic 5W-30 .20 to 120F(.30 to 40C) provides the best protection at all temperatures as well as improved starting with less oil consumption. 5W-30 40F and below (5C and below) is recommended for winter use, and works best in cold conditions. Oil Capacity The engine holds approximately 5/8 qt. (20 oz; 0.6 liter). Adding Oil • Check oil level before starting the engine. • Keep oil level at FULL. • Check level daily, or after every eight (8) hours. 1. Place engine level and clean around oil fill plug. (A) 2. Remove oil fill plug. Fill oil to point of overflowing. (B) 3. Replace plug before starting engine. A B Fuel Recommendation Kerosene • Use clean, fresh kerosene. Fresh kerosene prevents gum from forming in the fuel system or on essential carburetor parts. Purchase kerosene in quantity that can be used within 30 days. • To keep kerosene fresh and protect the engine use a Kerosene Additive. • Do not mix oil with kerosene. Adding Fuel 1. Replace cap before starting. 2. Clean area around black kerosene cap and remove. Fill tank to approximately 1-1/2 inches below top of neck to allow for fuel expansion (A). Be careful not to overfill. 3. Replace cap before starting. WARNING Kerosene and its vapors are extremely flammable and explosive. Fire or explosion can cause severe burns or death. WHEN ADDING FUEL • Turn engine OFF and let engine cool at least 2 minutes before removing fuel cap. • Fill fuel tank outdoors or in well-ventilated area. • Do not overfill fuel tank. • Keep kerosene away from sparks, open flames, pilot lights, heat, and other ignition sources. • Check fuel lines, tank, cap, and fittings frequently for cracks or leaks. Replace if necessary. 7 Starting Engine 1. Check oil level. 2. Fill kerosene tank with kerosene. 3. Fill petrol tank with petrol per the equipment manufacturer’s instructions. 4. Move CHOKE to choke position (A). 5. Move throttle control to fast position, if equipped. 6. Open kerosene shut off valve (B). 7. Push rocker switch to ON position (C). 8. Push primer bulb three times (D). 9. Grasp rope handle. Pull slowly until resistance is felt, then pull rapidly to start engine and avoid kickback (E). CAUTION This engine is shipped from Briggs & Stratton without oil. If you start the engine without oil, the engine will be damaged beyond repair and will not be covered under warranty. Rapid retraction of starter cord (kickback) will pull hand and arm toward engine faster than you can let go. Broken bones, fractures, bruises or sprains could result. •When starting engine, pull cord slowly until resistance is felt, then pull rapidly. •Direct coupled equipment components such as, but not limited to, blades, impellors, pulleys, sprockets, etc., must be securely attached. WARNING A B C D E Adjusting Choke After engine has started, slowly adjust choke to OPEN (A) position as engine warms up. A Operation Do not tip engine or equipment at angle which causes kerosene or petrol to spill. The manufacturer of the equipment on which this engine is installed specifies top speed at which the engine will be operated. DO NOT EXCEED this speed. WARNING Stopping Engine WARNING Do not stop engine by moving choke control to CHOKE. Backfire, or explosion can cause severe burns or death. Engine damage may occur. 1. Do not move choke lever. (A) 2. Push stop switch to OFF position (1). 3. Close kerosene shut off valve (2). Troubleshooting Starter Handle will Not Pull Place equipment on flat level surface. Remove all external equipment/engine loads before starting engine. Direct coupled equipment components such as, but not limited to, blades, impellers, pulleys, sprockets, etc., must be securely attached. Engine will Not Start Out of Fuel • Add kerosene to tank. • Prime engine. Engine Flooded • Set choke (if equipped) to OPEN/RUN position, and continue to pull starter handle. Spark Plug Fouling • Check an ensue the spark plug is clean. Check the gap with a feeler gage and reset to .76 mm or .030 in. if necessary. • Replace the spark plug if upon inspection the electrode is burned or worn. Engine is Smoking or Running Rough Engine may have been tipped during transport. • Check for fouled spark plug. • Check air cleaner filter for oil saturation. If clean but saturated, squeeze in clean, absorbant cloth to remove ALL EXCESS oil. If filter is dirty see page 11 for servicing air cleaner. A B C Need Assistance? Go to WARNING • Ensure fuel cap is in place before starting engine • Turn engine OFF and let engine cool at least 2 minutes before removing fuel cap. • Do not crank engine with spark plug removed. CAUTION If engine is tipped to transport equipment, to remove debris, to drain oil, etc., keep the spark plug side of engine up. 9 Engine Specifications Operation of this engine is for the application it was intended for. All the components used to build this engine assembly must remain in place for the proper operation of this engine. C...