Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Also Recommended for Use: • Safety glasses (ANSI Z87.1 approved safety glasses with side shields) • Air hose - 25 ft (7.5M), 3/8 inch diameter • Quick connector fitting - Use type I/M quick connect fittings that attach to 1/4 inch NPT thread • Hearing protection (ANSI S3.19-1974) in noisy environments • Respirator (NIOSH-approved) in dusty environments Verify Engine and Pump Oil Levels CAUTION! Any attempt to start the compressor before it has been properly serviced with the recommended oil may result in an engine and / or pump failure. 1. Place air compressor on a flat, level surface. 2. See “INSPECT ENGINE OIL LEVEL” on page 16 to verify engine oil level. 3. See “INSPECT PUMP OIL LEVEL” on page 17 to verify pump oil level. Add Fuel NOTE: This engine is certified to operate on gasoline. Exhaust Emission Control System: EM (Engine Modifications). WARNING Fuel and its vapors are extremely flammable and explosive. Fire or explosion can cause severe burns or death. WHEN ADDING FUEL • Turn compressor OFF and let it cool at least 2 minutes before removing fuel cap. Loosen cap slowly to relieve pressure in tank. • Fill fuel tank outdoors. • DO NOT overfill tank.Allow space for fuel expansion. • If fuel spills, wait until it evaporates before starting engine. • Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition sources. • DO NOT light a cigarette or smoke. 1. Use clean, fresh, regular UNLEADED fuel with a minimum of 85 octane. DO NOT use fuel which contains Methanol. DO NOT mix oil with fuel. 2. Clean area around Fuel Tank Cap, remove Fuel Tank Cap. 6 ASSEMBLY 3. Slowly add fuel to fuel tank. Fill to red fuel level indicator (see Figure 1). Be careful not to overfill tank. Figure 1 - Add Fuel Fuel Level Indicator 4. Replace fuel cap and wait for any spilled fuel to evaporate. CAUTION! Some fuels, called oxygenated or reformulated fuel, are fuels blended with alcohols or ethers. Excessive amounts of these blends can damage the fuel system or cause performance problems. If any undesirable operating indications occur, use fuel with a lower percentage of alcohol or ether. Fresh fuel prevents gum from forming in the fuel system or on essential carburetor parts. Purchase only quantities of fuel that can be used within 30 days. Install Pump Oil Breather Cap 1. Ensure compressor is resting on a flat, level surface. 2. Open Drain Valves (rotate fully counterclockwise) to release residual air pressure build-up in air tanks (see Figure 2). Figure 2 Drain Valve Drain Valve shown in Open position CAUTION Residual compressed air in pump can propel oil and cause soft tissue damage to exposed skin or eyes leading to severe injury. • Always wear ANSI Z87.1 approved safety glasses with side shields. 3. Remove and discard shipping cap. 4. Install pump oil breather cap into the oil fill (see Figure 3). 5. Wipe up any spilled oil. 6. Close Drain Valves (rotate fully clockwise) (see Figure 2 earlier). CAUTION • Damage to equipment resulting from failure to follow this instruction will void warranty. Serious damage may result if operating the unit with insufficient oil. Inspect oil level daily or with each use. Figure 3 - Install Pump Oil Breather Cap Oil Drain Plug Oil Fill Location MAXIMUM Oil Level Oil Breather Cap PROPER Oil Level 7 FEATURES AND CONTROLS 8 Air Cleaner: Protects engine by filtering dust and debris out of intake air. Air Compressor Pump: Pump compresses air into tank. Check Valve: When unit is operating, Check Valve is “open”, allowing air to enter tank.At “cut-out” pressure, Check Valve closes, preventing air from flowing back into pump.Check Valve is not serviceable by user. Choke Lever: Used when starting a cold engine. Data Tag: (not shown) The data tag contains serial number, model number, and revision number information. Drain Valve: Valves are located near bottom of each air tank at the handle end and are used to drain condensation. Engine Information: Stamped on side of valve cover. Provides model, type and trim number of engine. Please have this information readily available when calling for assistance. Engine Speed Lever: Used to adjust engine speed to control pump output. Fuel Shutoff Valve: Used for turning engine’s fuel supply on and off. Fuel Tank: Capacity of one (1) U.S. gallon. Fuel Tank Cap: Inspect and fill gas tank here. Engine Oil Fill Cap: Fill engine with oil here. Compressor Oil Fill Location: Fill pump with oil here.Oil level sight glass indicates pump oil level. On/Off Switch: Set this switch to ON before using Starter Handle. Set switch to OFF to switch off engine. Outlet Pressure Gauge: Indicates air pressure at Quick Connect Fitting. Pressure Control: Controls air pressure delivered to Quick Connect Fitting; can be secured with locking ring. Pressure Release Valve: Located adjacent to Check Valve, valve automatically releases air from compressor components at “cut-out” pressure or when unit is shut off.Valve is not adjustable or serviceable by user. Pilot Valve...