Оценок - , средний балл:
(
)
)
Производитель: Harbor Freight Tools
Размер: 324.28 kb
Название файла: 95267.pdf
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
If you are using the tool outdoors, use an extension cord rated for outdoor use. (signified by “WA” on the jacket). Note: Do not make the extension cord connection underwater. 17. Do not pump hazardous materials. Do not pump explosive or flammable materials such as Fuel Oil, Kerosene, Gasoline etc. Do not pump in close proximity to flammable or explosive materials. Do not pump fats, oils, salt or waste water. This Pump is designed to move clean or dirty water. Do not pump hot liquid. 18. Water transfers in cycles. Do not attempt to manipulate the switch to keep pump running continuously. It is meant to shut off intermittently. Doing so will damage the pump. Note: Performance of this pump (if powered by line voltage) may vary depending on variations in local line voltage. Extension cord usage may also affect pump performance. Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpacking, check to make sure the parts listed on page 8 are included. If any parts are missing or broken, please call Harbor Freight Tools at: 1-800-444-3353. Installation Reminder: This pump should be plugged into an outlet fitted with a Ground Fault Circuit Interrupter (GFCI). Note: Hose connection is covered on page 5. 1. Make sure the pump rests on a flat, level, and solid foundation. Never operate on earth, clay, sand, or gravel surfaces. 2. Never suspend the pump from the power cord or discharge pipe. You may firmly attach a rope to the carry handle. 3. Keep the pump inlet openings, near the suction base, clear of debris. 4. Avoid installation in areas of extreme heat or cold. 5. If the piping you install runs in excess of ten feet, it is recommended you use a check valve (not included) to prevent back flow, which could lead to rapid cycling. To avoid air locks in the pump, drill a 1/8” hole in the piping between the check valve and the pump. Sump Installation (all instructions above apply) 1. The sump pit must have a minimum diameter of 11” and maximum depth of 18 feet. 2. Construct the pit of tile, plastic, concrete, or steel. 3. Set the pump on a brick or block slightly smaller than the pit. Fill the pit with clean 1” or larger stones to surround the lower half of the pump to keep it stable. The stones should be large enough to not clog any of the inlets. 4. Test pump (see Operation on page 6). 5. Install a sump cover to protect the pump from falling debris. Installation (continued) Hose Connection: The Universal Fitting (42), in Figure B, connects to various hose sizes. The hoses should be connected using a step nipple (not included). The 1” and 1-1/4” hoses should also be secured with hose clamps (not included). The largest connection (1-1/2”) will yield the greatest flow. The top of the Universal Fitting may be removed to fit on various size hoses (see Figure B). Use a knife to gently trim any unneeded material. Note: Use a pipe joint sealant to ensure air tight operation. Note: (Optional) To reduce vibration and noise, a short section of rubber hose (1-1/4” x 1- 3/8” inside dia.) may be attached to the discharge line, using clamps (hose and clamps not included). Figure A Hose Fitting Sizes 1-1/2” 1-1/4” 1” G Vent Valve Figure B Float Switch (1) Figure C (Removing Base to clean Impeller) Connect the Universal Adapter (42) here. Figure C Warning: Do not run the pump dry. It will increase wear to the unit and possibly cause seal damage. Note: This pump has a built-in thermal protector for the motor, which automatically shuts it off to avoid overheating. After it cools, it will cycle back on. Wait for the cycle to continue. Do not try to turn on the pump manually after it has cut off. 1. Plug unit into an outlet fitted with a Ground Fault Circuit Interrupter (GFCI). 2. The pump will automatically turn on when the water level, or the sump, has filled to approximately 3” above the base. It will stop when the water level drops below 3”. It will continue to recycle thereafter. 3. Check that the discharge water travels several feet from the foundation. Float Switch Adjustment There is a Cable Clip (11) that is connected to the Pump Housing (13). The Float Switch (1) cord snaps into the Cable Clip (11) (see page 8). You can adjust the level that the Pump turns on by adjusting the length of the Float Switch cord. Note: If air bubbles are spotted around the handle or pressure switch, this is normal. It is trapped air escaping from the unit. This pump is equipped with a de-aerating device which removes air locked in the pump. Also, if the water level drops below the Vent Valve (see page 7 figure B), some water might purge from the pump from the Vent Valve. This is normal. More on air escape is covered in the troubleshooting section. Operation Maintenance Pump Mot...