Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
11. Drain compressor every day. Do not allow moisture to build up inside the compressor. Do not allow compressor to sit pressurized for longer than one hour. 12. Make sure all equipment is rated to the appropriate capacity. Adjust the output air pressure to the tool’s operating capacity. 13. Avoid body injury. Never direct the air outlet at persons or animals. REV 11/04 SKU 90385 For technical questions, please call 1-800-444-3353. Page 5 GROUNDING WARNING! Improperly connecting the grounding wire can result in the risk of electric shock. Check with a qualfified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet installed by a qualified electrician. Grounded Tools: Tools with Three Prong Plugs 1. Tools marked with “Grounding Required” have a three wire cord and three prong grounding plug. The plug must be connected to a properly grounded outlet. If the tool should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user, reducing the risk of electric shock. (See Figure A.) 2. The grounding prong in the plug is connected through the green wire inside the cord to the grounding system in the tool. The green wire in the cord must be the only wire connected to the tool’s grounding system and must never be attached to an electrically “live” terminal. (See Figure A.) 3. Your tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like those in the following illustration. (See Figure A.) Figure A Figure B Double Insulated Tools: Tools with Two Prong Plugs 4. Tools marked “Double Insulated” do not require grounding. They have a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the National Electrical Code. (See Figure B on page 6.) 5. Double insulated tools may be used in either of the 120 volt outlets shown in the preceding illustration. (See Figure B on page 6.) SKU 90385 For technical questions, please call 1-800-444-3353. Page 6 SYMBOLOGY Table B UNPACKING When unpacking, check to make sure that all the parts are included. Refer to the Assembly section, and the Assembly Drawing and Parts List at the end of this manual. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. In addition, this unit is packed with a rubber block to help prevent damage to the Motor Cover (82) during shipment, shown below. This block should be removed BEFORE use of this compressor, it can interfere with proper operation. It may be set aside for additional shipping purposes, if desired. REV 05/05 SKU 90385 For technical questions, please call 1-800-444-3353. Page 7 ASSEMBLY INSTRUCTIONS Warning: Fill compressor with oil before using; running without oil, or with low oil voids warranty. Do not plug in the Air Compressor until you are ready to use it, as set forth below. Adding Oil 1. Unscrew (do not pull)the Oil Plug (79). (See Figure C.) 2. Check the level of the oil by viewing the Oil Leveler (72) window (below the Oil Plug). Note: Fill the oil tank with approximately 25 ounces of oil. 3. Add 30-weight, non-detergent oil through the fill hole as necessary, but do not overfill. Screw in the Oil Plug, being careful not to strip the plastic threads. Hose Connections 1. Close the Air Control Valve (69), right or left. 2. Connect the high pressure air hose to the air outlet. The outlet is 1/4” NPT. For easy connection or removal, a quick coupler (not supplied) should be installed on the end of the outlet. To extend the life of your air tools, it is recommended to install an oiler and water filter in series with the air output line of the Air Compressor as shown below. (79) Figure C Figure D 3. Connect the high pressure air hose to the air tool. 4. Turn the Air Control Valve to the middle position to allow the air to pass. Warning: Do not remove the factory sealed Air Control Valve (69); removal voids warranty. Air Filter If not already attached, mount the Air Filter (85) to the Cylinder Head (2) before using the air compressor. REV 04/04 SKU 90385 For technical questions, please call 1-800-444-3353. Page 8 NOTE: Actual product design may vary slightly from that shown. NOTE: Actual product design may vary slightly from that shown. S Turning Compressor On 1. Plug the power cord into an electrical outlet with a grounding prong. 2. Pull up on the Auto/Off Pressure Switch (66) to turn on. Push down on the Switch to shut off. 3. Allow the Tank to fill to 80 PSI before...