Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. (California Health & Safety Code § 25249.5, et seq.) Note: Performance of the compressor (if powered by line voltage) may vary depending on variations in local line voltage. Extension cord usage may also affect tool performance. Unpacking When unpacking, check to make sure the parts listed on page 8 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Voltage Warning Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is about the same as that specified on the nameplate of the tool. If one says 120V and the other says 110 VAC, then there will be no complications. Never try to plug a 110V tool into a 220V outlet, or the other way around. The plug and outlet have completely different shapes. This is because the power source with a voltage greater than that specified on the tool can result in SERIOUS INJURY to the user - as well as damage the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with voltage (110 VAC) less than the nameplate rating (220 VAC) is harmful to the motor. Extension Cords If your tool is double insulated and has a two-prong plug, you may use either a two or three-prong extension cord. If your tool has a grounded, three-prong plug, you must use a three prong extension cord with three-prong receptacles. Only use rounded jacket extension cords, preferably listed by the Underwriters Laboratory (UL). Make sure the cord is rated for outdoor use if you plan on using the tool outside; if you plan on indoor use you may also use an outdoor rated cord. Extension cords rated for outdoor use have the letters “WA” on the cord jacket. The extension cord must have a minimum wire size depending on the amperage of the tool and the length of the extension cord. This size is signified by its AWG (American Wire Gauge) rating; the smaller the gauge, the greater the cable’s capacity. If you are using two or more cords, the total length of the combined cords must be used to determine the minimum AWG rating. Each of the cords used must meet this rating. The chart below is used to determine the rating required according to the length of the cord (s). The amps of your tool are found either in this manual or on the nameplate of the tool. Always inspect extension cords for any damage. If there are any loose, frayed or exposed wires, damaged insulation, or defective connections, replace the cord. Harbor Freight Tools can supply UL listed and outdoor rated cords in multiple AWG ratings if needed. SETUP Note: Before operating, make sure the Compressor is set up in a well-ventilated area, on a flat, level, solid surface well away from any flammable objects, such as drapes. Never paint in an area without proper ventilation, or near possible ignition sources. FIGURE 1 Handle (33) Adjusting Screw (29) Pressure Meter (37) Switch (5) Air Outlet (38) Cord (2) Filter (42) Drain (43) Operation Insert the Plug (1) into a power outlet. When you are completely ready, turn on the Compressor by moving the rocker Switch (5). Air pressure is regulated using the Adjusting Screw (29). Loosening the Adjusting Screw allows excess pressure to escape through the valve in the center. Tightening the Adjusting Screw increases the pressure built up before air blows out through the valve. Read the pressure level on the Pressure Meter (37). Caution! The Adjusting Screw (29) can come out if loosened excessively. Shut off the Compressor after use. REV 05c, 07d Maintenance While operating the Compressor, make sure the Filter Cover (28) (see Assembly Drawing on page 8), and the motor fan, are free of obstructions. Periodically remove the Filter Cover (28) and make sure it is clean. It serves as a filter for purifying the air the compressor takes in. FIGURE 2Drain (43) The Filter (42) cup will fill with moisture from air that flows through the filter. After each use, push the Drain (43) under the cup to drain off the moisture. See FIGURE 2. Note: There are no user-serviceable parts in your Air Brush Compressor. Service should always be done by a qualified service technician. Note: Never use any organic solvents such as thinner, alcohol, trichloroethylene, etc. to clean the Filter Bowl. Only use dishwashing liquid. PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE...