Оценок - , средний балл:
(
)
)
Производитель: Harbor Freight Tools
Размер: 825.27 kb
Название файла: 66399.pdf
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
To reduce the risk of vibration-related injury: Anyone using vibrating tools regularly or for an extended period should first be examined by a doctor and then have regular medical check-ups to ensure medical problems are not being caused or worsened from use. Pregnant women or people who have impaired blood circulation to the hand, past hand injuries, nervous system disorders, diabetes, or Raynaud’s Disease should not use this tool. If you feel any symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible. SAVE THESE INSTRUCTIONS. SPECIFICATIONS Maximum Air Pressure 115 PSI Speed Fills Car Tire in Approx. 3 Minutes Air Flow 1.3 SCFM @ 40 PSI 0.9 SCFM @ 90 PSI Rated Air Pressure 0-115 Maximum Power 12VDC, 30 AMPS Permanently Lubricated Do not add oil or any other lubricant INITIAL TOOL SET UP/ ASSEMBLY Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. Unpacking When unpacking, make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown throughout the manual as soon as possible. • This air tool may be shipped with a protective plug covering the air inlet. Remove this plug before set up. Note: Air flow, and therefore tool performance, can be hindered by undersized air supply components. 1. The air hose must be long enough to reach the work area with enough extra length to allow free movement while working. 2. Turn the tool’s On/Off switch to the “OFF” position; refer to Operation section for description of controls. 3. Inspect the air connections for leaks. Repair any leaks found. OPERATING INSTRUCTIONS Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Inspect tool before use, looking for damaged, loose, and missing parts. If any problems are found, do not use tool until repaired. Tool Set Up TO PREVENT SERIOUS INJURY: Do not adjust or tamper with any control or component in a way not specifically explained within this manual. Improper adjustment can result in tool failure or other serious hazards. Work Piece and Work Area Set Up 1. Designate a work area that is clean and well-lit. The work area must not allow access by children or pets to prevent distraction and injury. 2. Route the air hose along a safe route to reach the work area without creating a tripping hazard or exposing the air hose to possible damage. The air hose must be long enough to reach the work area with enough extra length to allow free movement while working. General Assembly and Operating Instructions 1. Set tool on a dry, flat, level surface. 2. To prevent accidents, turn the On/Off Switch (25) to the “OFF” position. 3. Attach the quick coupler of coiled Air Hose (59) to male connector at the end of Rubber Hose (53). 4. Fig. 1Air House (59) Coupler CollarMale ConnectorPull back on collar of Air Hose’s coupler. Then firmly insert connector into coupler. (See Figure 1.) Release collar, which will snap connector in place. Pull lightly on both hoses to ensure proper locking in the coupler. 5. Attach the clamps on the Power Cord (27) onto the 12V automotive battery (not included) power source. a. Connect RED clamp of the Compressor to the positive (+) terminal of the battery. b. Connect BLACK terminal of the Compressor to a good ground source on the engine block. WARNING! Do NOT connect it to the other battery terminal. c. Note: The power source must not exceed 12V. 6. WARNING! Failure to follow the following steps can lead to a blown fuse. 7. Be sure the valve stem is clean and free of dirt. REV 10a 8. Fig. 2On/Off Switch (25) Fuse (26) Flip the On/Off Switch (25) to the “ON” position. (See Fig. 2.) Note: Turn unit on before connecting to tire valve to prevent blowing the fuse. 9. Holding the Air Nozzle Grip (56), thread the Air Nozzle (55) onto the valve stem of the item to be inflated, or attach an alternate Inflator Nozzle (61,62,63). 10. NOTE: When inflating, finger-tighten Air Nozzle only. Do not over-tighten. 11. Fig. 3Monitor the Pressure Gauge carefully to avoid over-inflating the item. (See Fig. 3, above.) 12. Continue inflating until the recommended pressure is reached. 13. Stop the compressor by clicking the On/ Off Switch to its “OFF” position. 14. Remove the Air Nozzle by unthreading it from the valve stem. NOTE: In the case of a football or soccer ball, pull the Needle Nozzle (63), out of the ball valve orifice. NOTE: After disconnecting the Compressor, it is advisable to verify tire pressure with a tire pressure gauge (not included). NOTE: Remember to replace the valve cap, where applicable. 15. If the tire pres...