Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Safety Warnings WARNING Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. 1. Tighten and release evenly and slowly. Only use hand tools to tighten/release. Do not use any air, electric, or impact tools with this tool. Only operate this tool with a 3/4. socket and ratchet, 3/4. combination wrench, or other applicable hand tools. Power, air, or electric tools may compress the spring too quickly, leading to injury. 2. Use provided pins to secure spring in place before use. 3. Set compressed spring in safe area. Be careful when spring is compressed. Do not drop or jar spring. Doing so might result in the spring forcefully flying free, causing personal injury or damage. 4. Do not use on springs larger than 7. diameter. 5. Wear ANSI-approved safety goggles and heavy-duty work gloves during use. 6. Inspect before use; do not use if parts loose or damaged. 7. Observe work area conditions. Keep work area clean and well lit. 8. Use the right tool for the job. Do not attempt to force a small tool or attachment to do the work of a larger industrial tool. There are certain applications for which this tool was designed. Do not modify this tool and do not use this tool for a purpose for which it was not intended. 9. Stay alert. Watch what you are doing, use common sense. Do not operate any tool when you are tired. 10. Check for damaged parts. Before using any tool, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment and binding of moving parts; any broken parts or mounting fixtures; and any other condition that may affect proper operation. Any part that is damaged should be properly repaired or replaced by a qualified technician. 11. Replacement parts and accessories. When servicing, use only identical replacement parts. Use of any other parts will void the warranty. Only use accessories intended for use with this tool. 12. Do not operate tool if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the tool. 13. For your safety, maintenance should be performed regularly by a qualified technician. Have qualified service technician inspect this tool annually. 14. Only use this tool with MacPherson struts. Do not use with high pitched springs. 15. If spring coils do not compress evenly, loosen the adjusting screw, reposition the strut spring, and retry. 16. Before initial use, apply grease to the Adjustment Bolt. Also, apply grease periodically during use. 17. When reaching the maximum torque (15 ft-lb) by tightening the Adjustment Bolt, discontinue, and loosen the screw. Reposition and retry. 18. Support vehicle on jack stands before working on it. 19. Follow instructions and precautions in vehicle’s service manual. 20. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Assembly Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use of this product. 1. Insert the Adjustment Bolt (6) with the Hex end up, through the hole in the center of the Plain Axle (13). 2. Slide the Compression Spacer (20) onto the Adjustment Bolt (6) before continuing through the center hole on the Threaded Axle (10). 3. Secure Adjustment Bolt (6) with two Nuts (16). Operation Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use of this product. Remove MacPherson struts from the vehicle before attempting repairs. Put the struts in a MacPherson Strut Vise prior to using the Strut Spring Compressor. Only use hand tools with the Strut Spring Compressor. Do not use any air, electric, or impact tools with this tool. Only operate this tool with a 3/4. socket and ratchet, 3/4. combination wrench, or other applicable hand tool. Power, air, or electric tools may compress the spring too rapidly, leading to injury. 1. Follow the vehicle service manual’s instructions to remove the MacPherson Strut from the vehicle. 2. Position the strut into a strut vise. 3. Shut the vise and tighten. 4. Open the Spring Compressor up to 8.. Do not open more than 8. or a long strut may slip off of the tool. 5. Make sure the hex nut on top of the Adjustment Bolt (6) is facing up. 6. Before clamping the spring, slip the Safety Ring (19) over the Hooks (5,7) as a safety precaution should the strut break loose. The Safety Ring (19) will keep the cla...