Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
The speed of the ratchet is adjusted by handle paddle position, but the torque is not changed. Model H8208 50-Piece Air Tool Set -5- Impact Wrench Your new single hammer V2" drive impact wrench (Figure 1) will generate up to 230 ft/lbs. of torque. Only use thick-walled impact sockets with this air tool. The common thin-walled chrome sockets may explode if used as impact sockets causing serious injury. At the end of the handle you can adjust the torque setting by pushing the knob in and turning the knob to 1, 2, 3, or 4; 1 is the lowest torque setting. To change the impact rotation, push the slide button toward the front of the gun for clockwise rotation and to the rear for counterclockwise rotation. Blowgun The blowgun has a variety of tips and adapters (Figure 1). Always disconnect the blowgun from air before changing tips. The blowgun safety tip has two holes in the side to help prevent high pressure air injection injuries if the blowgun is accidently pushed against the skin. The air is intended to exhaust out of the two holes in the sides of the adapter and not into your skin, helping to prevent severe air embolism injury. The other tips and adapters are intended for high pressure use where side leakage is not wanted. The jet tip directs a high velocity jet of air to a pinpoint location, the brass-barbed push-on hose tip connects your blowgun to rubber hoses of various size. To check for leaks where the port is just a drilled hole, use the direct pressure adapter with the rubberized tip that seals the port of the system being pressurized. To fill a soccer ball for example, you would also use this adapter but with the ball inflator tip. Never over-inflate any ball, or it can explode causing severe injury. Air Hammer Your new air hammer (Figure 1) is a great tool for chipping and chiseling welds, stone, wood, tiles, grout and many other materials. But remember, never change chisels with the air hammer still connected to the air supply. Before your first use, position the chisel retaining spring onto the end of the air hammer by threading it on in a clockwise rotation until the retainer is completely seated and it stops. Three of the most common chisels are included in this set. To install and remove a chisel, push the chisel retaining spring tang (Figure 3), so the retainer spring "U" clears the chisel retaining shoulder and insert or remove a chisel of your choice. Note: If you have difficultly bending the retainer spring to fit the bit, loosen or remove the spring and insert the bit into the spring prior to threading it on the hammer. Figure 3. Chisel installation. -6- Model H8208 50-Piece Air Tool Set Make sure that when the chisel is installed, the retainer spring "U" is holding the chisel as shown in (Figure 4). Figure 4. Safe chisel position. To control the chisel hammer rate and the hammering force, turn the knurled thumb knob on the end of the handle. Rotating clockwise reduces the hammer rate and the hammering force. Tire Inflators This set contains two tire inflators (Figure 1). Before filling tires, always know what the maximum tire inflation pressure is. NEVER overfill any tire, or it can explode causing severe injury. The stubby tire inflator (Figure 1) is used for general tire inflation where the valve stem is easily accessible. The long neck version is for filling dual truck tires or other hard to reach valve stems. Daily Maintenance Your air tool MUST have 2-6 drops of oil directly dropped into the air fitting before each use. In addition, we recommend using an in-line filter, lubricator, and regulator, as shown in Figure 2. If an inline lubricator is not used, add 2-3 drops of oil into the tool air inlet every 2 hours of continued use. These procedures should be done after each use: • Before putting the air tool away, put 2-6 drops of oil into the air supply fitting. Note: For the impact wrench, you must also remove the 4mm plug, put 2-6 drops of oil into the hole, and reinstall the plug. • Wipe the tool exterior and sockets, bits, or chisels with a slightly oiled cloth. Your goal is to leave a light film of oil on the tools to prevent rust. Model H8208 50-Piece Air Tool Set -7- AIR IMPACT WRENCH 1 PH8208001 DETENT PIN 2 PH8208002 COMPRESSION SPRING 3 PSS26M SET SCREW M5-.8 X 6 4 PS79M PHLP HD SCR M3-.5 X 8 5 PH8208005 COVER 6 PH8208006 TRIGGER 7 PRP98M ROLL PIN 3 X 16 8 PH8208008 DOG-POINT SET SCREW 9 PH8208009 REGULATOR 10 PORS009 O-RING 8.5 X 1.5 11 PH8208011 COMPRESSION SPRING 12 PH8208012 DUST COVER 13 PH8208013 PLUG 14 PH8208014 COMPRESSION SPRING 15 PH8208015 STEEL BALL 16 PH8208016 SHOULDER WASHER 17 PH8208017 VALVE 18 PORP007 O-RING 6.8 X 1.9 P7 19 PH8208019 VALVE 20 PH8208020 SLEEVE 21 PH8208021 RUBBER CUSHION 22 PSB15M CAP SCREW M5-.8 X 20 23 PLW01M LOCK WASHER 5MM -8- 24 PH8208024 COVER 25 PH8208025 GASKET 26 PH8208026 END PLATE 27 PH8208027 SPECIAL CAP SCREW 28 PH8208028 CYLINDER 29 PH8208029 DOWEL PIN 30 PH820803...