Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
There are certain applications for which this tool was designed. Do not modify this tool and do not use this tool for a purpose for which it was not intended. 17. Do not operate tool if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the tool. 18. Pacemaker safety warning. People with pacemakers should consult with their physician(s) before using this product; operation of equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker. Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpacking, check to make sure all parts are included. Refer to the parts list and assembly diagram on page 7 and 8. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual. Operation 1. Connect drain hose to the Universal Adapter (47) discharge fitting. This hose should be long enough to drain away from the reservoir being pumped. See installation examples on the next page. 2. If the pump needs to be lowered into a pool or other deep reservoir, attach a rope to the pump handle and lower into position. Never suspend the pump from the power cord or discharge pipe. The pump should rest on a flat, level, and solid foundation. Never operate on earth, clay, sand, or gravel surfaces. Keep the pump inlet opening clear of debris. If the drain piping runs in excess of 10 feet, it is recommended to use a check valve (not included) to prevent back flow. To avoid air locks in the pump, drill an 1/8 inch hole in the piping, between the check valve and the pump. Refer to the illustration on the next page. Warning: Never use the line cord to carry the pump. Do not run the pump dry. It will increase wear to the unit and cause possible seal damage. 3. Connect the Power Cable to the Ground Fault Interrupter receptacle to begin pumping. Caution: The Float Switch must be floating in water for the pump to operate. It is meant to shut off intermittently. Do not attempt to manipulate the switch to keep the pump running continuously. Doing so will damage the pump. Warning: Never allow the power cord or extension cord connection (if used) to come in contact with ground water. Note: Performance of this pump may vary depending on variations in local line voltage. Extension cord usage may also affect tool performance. Ground Fault Circuit Interrupter Danger Electrical Connection ON H2O H2O H2O H2O DANGER Never Touch Float (1) or Water During Pump Operation 1/8” HOLE Recommended Check Valve Removing Underground Water Accumulated From Rain Gutter ON H2O H2O OFF ON - OFF Switch Operation House Sump Troubleshooting SYMPTOM CAUSE SOLUTION The pump will not start No power Impeller blocked Thermal protection shutdown Entangled Float Switch Check power source; Reset GFCI Free impeller (see Maint.) Allow pump to cool down; auto restart Check Float Switch The pump operates but pumps little or no water Pump submerged too deep Discharge pipe bent Suction grid clogged Air locked in suction base Optional check valve stuck or installed backwards Reduce submersion depth Free bends from pipe Clean suction grid Turn off pump for 10 seconds Examine check valve Excessive noise or vibration Worn bearings Debris in impeller Have a qualified technician repair Clean out impeller inlet Pump starts and stops too frequently Water temperature too high Defective or entangled Float Switch Water backflow Never use pump in water over 95 degrees F. Replace or reposition switch Install a check valve at the outlet Maintenance Warning: Disconnect power before performing any maintenance. 1. Periodically clean the suction section of the pump, removing any foreign particles. Run in clean water to flush out system. 2. To remove particles stuck on the impeller, remove the screws (19) on the Base Cover (17), and pull Base (18) off. 3. Any other maintenance must be done by a qualified technician. Base (18) Base Cover (17) Screws (19) Parts List Part Description Q’ty 1 Float Switch 1 2 Power cable & plug 1 3 Nut 2 4 Plastic handle 1 6 Washer 3 7 Screw 3 8 Outer pump housing 1 9 Screw 1 10 O-ring 2 11 Rear housing motor 2 12 Cord Jacket 1 13 Cord clip 1 14 Cord clip 1 15 Screw 1 16 Condenser 2 17 Base cover 1 18 Base 1 19 Screw 3 20 Nut 1 21 Impeller 1 22 Adjustable washer 1 23 Seal washer 1 24 Locating ring 1 Part Description Q’ty 25 Screw 6 26 Press ring 1 27 O-ring 1 28 Skeleton seal 3 29 Front cover 1 30 Front bushing 1 31 Bearing 1 32 Rotor 1 33 Under washer 2 34 Stator 1 35 Spring washer 1 36 Screw 1 37 Earthing wire 1 38 Rear cover 1 39 Washer 1 40 Valve bush 1 41 Ball 1 42 O-ring 1 43...