Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
A great deal of dedication and passion went into designing and building this no-compromise, high performance unit. It was concieved to be a dedicated tool for the “conessieur” bassist. Before using the Bass Buddy please read ALL the instructions . Reading this manual will enable you to get the best performance from it and it will give you many years of service. • Keep all original packing. • Never use this product in the vicinity of water or liquids. • Do not operate this unit with a damaged power cord or plug or if the unit is damaged. • Do not locate this unit near any heat source. • This unit must be connected only to the power unit supplied. • For safety do not leave the power supply plugged into a power source for long periods of time when not in use. • Do not use the Bass Buddy power supply unit on any other aparatus. • To prevent damage to unit from battery leakage, always use high-quality brand name batteries. Remove any batteries from unit if stored for a pieriod of time. • Do not use Monster brand instrument cables as they are not compatible with PJB electronics. Using a Monster cables can damage PJB jack sockets and is not covered by PJB waranty. OVERVIEW OF THE BASS BUDDY • Switch able Active / Passive input matches both magnetic and piezo pickups. • Powerful 5 Band Graphic EQ. • Natural Sounding Optical Limiter. • Hi-fi Stereo Headphone Output. • Low Noise Pre-amp output. • World-class Studio Quality, Balanced Line output. • 10 watt RMS wideband amplifier. • Worldwide AC voltage operation. • Works on two 9-volt batteries. • Ultra low noise, low distortion state of the art electronics. FRONT & BACK PANEL OVERVIEW †U.©?.©?.©?.©?.©?.© MAXVOLUMEAUX INPUTSPEAKER 8.LINES OUTDC IN 18-VOLTS/N: MINXXXXXMAXACTIVEMINVOLUME160Hz50Hz+18dB0dB630Hz2.5KHzPASSIVEBASS INPUT-18dB+18dB0dB12KHzMAXCOMPRESSIONMINOFFONOFFHEADPHONE-18dBONPOWER9-VOLT9-VOLT 1. PASSSIVE/ ACTIVE BASS INPUT SWITCH. This switch allows you to match the BassBuddy to match either active or passive basses either with magnetic or piezo pickups. PASSIVE - Higher sensitivity, high impedance input (120mV/ 4.7M.). For bass instruments that do not have active electronics, suited for older ‘vintage’ basses. This setting is precisely matched to high impedance pickups enabling them to faithfully reproduce the true frequency and dynamic range of the instrument. ACTIVE- Lower sensitivity input setting (300mV/100K.) for basses with onboard electronics. Input matched for low signal to noise ratio and optimum transfer function of electrical signal from modern high-end basses. 2. VOLUME CONTROL. This is the volume control for bass input only. It does not control the level of the stereo auxiliary input socket (14) on back panel. When setting up your tone or plugging in your instrument, you should keep this control at a low level. All instruments are different when it comes to how much output is from the pickups. Likewise for players: depending on how hard or soft you play. 3. INSTRUMENT INPUT JACK. This is a standard . inch mono jack socket. We recommend that you DO NOT use “Monster” Brand cables because we have found compatibility issues with their jack plugs and our input sockets. USING “MONSTER” BRAND CABLES CAN DAMAGE THE INPUT JACK OR OTHER SOCKETS ON THE BASS BUDDY Should any damage occur from using MONSTER CABLES warrantee for repairs to unit are not covered under PJB warranty. 4. 5-BAND GRAPHIC EQUALIZER. This is a dedicated bass instrument equalizer designed to give you optimized tone of your instrument. The frequency bands have been set precisely so that your desired tone can be achieved with the minimum amount of sliders. The EQ filters are set at: 60Hz -160Hz - 630Hz - 2.5KHz and 12KHz with 18dB of boost or cut. This EQ typically has more control than other equalizers on your sound, so do not use too much boost as this can overdrive other electronic components in your chain. Be careful not to use excessive boost on lower frequencies as you may end up damaging your headphones. If you hear distorted tones on the lower notes, this could be you headphones overloaded. Back off the volume immediately. 5. COMPRESSION ADJUSTMENT LEVEL. This will vary the level of the limiter threshold. The compression ratio is 3dB to 1. Adjust this to suit your playing style and output power of instrument. Note that turning this control clockwise increases the threshold level and so reduces compression. More compression is added by turning the control counter-clockwise, like backing off the volume control. 6. HEADPHONE OUTPUT JACK. This jack accepts . inch stereo headphone jacks. A . inch to mini jack adaptor plug is supplied for headphones with smaller jack plugs. 7. LIMITER INDICATOR. This blue L.E.D (Light Emitting Diode) will light up when the signal is being compressed. This will vary on how hard the instrument is played and how the threshold is adjusted 8. LIMITER ON/OFF SWITCH. Sends signal through limiter or bypass. 9. POWER ON/OFF SWITCH. 10. POWER LED INDICATOR Wi...