Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
To turn the unit on, flip the switch to the “I” position. Lamps: The positioning of the lamps is pre-set and does not require any type of adjustment. Improperly positioned lamps will create deep spots of color in the flame. Should the lamps need adjustment due shifting during transit or after the replacement of a lamp, the lamps may be angled slightly to overcome any heavy color wash. Should the lamps positioning become incorrectly, adjust them as follows: 1. To properly position the lamp the unit must be on. Use an insulated screwdriver to make any adjustment to the lamps position. 2. The amber lamps should be angled to focused on the lower half of the silk drape. 3. Position the blue lamp to shine directly in the center of silk drape. 4. All lamps will eventually fade or fail. Replacements lamps are available from your dealer. Silk Flame: Your silk flame has been specially designed and hand cut from fine silk to interact with the airflow and lights to create the illusion of a flame. Each silk drape is applied prior to shipment and should be in the correct position. The silk drape has a life of approximately one month when used continuously in a clean environment. Additional silk drapes may be purchased through your dealer (part number Z-FLAMEBOWL7SILK). ©American DJ Supply® - - Fire Bowl™ Instruction Manual Page 4 Fire Bowl™ Set-Up/Operation Cont. Repositioning The Flame (Silk Drape): You may wish to reposition the flame drape to customize the effect. 1. Move the flame drape along the flame attachment rail by sliding the magnetic ends along the rail. 2. For best results, do not stretch out the ends of the silk drape as tight as it can get along the bottom. For a more realistic effect allow some play between the two ends of the silk drape, move the magnets slightly away from the side of the casing to achieve a more realistic flame effect. 3. For best results; experiment with the flame position. Slight changes in the position of the silk drape can drastically change the effect. Fire Bowl™ Silk Drape If the silk drape becomes creased, you may iron the flame using a nondrip iron on a low setting. Do not steam iron. If the silk drape becomes frayed, you may use a sharp pair of scissors to carefully cut the loose silk strands. The silk drapes may become frayed after a period of four weeks. Fire Bowl™ Cleaning Fixture Cleaning: Due to fog residue, smoke, and dust cleaning should be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates (I.e. smoke, fog residue, dust, dew). In heavy club use we recommend cleaning on a monthly basis. Periodic cleaning will ensure longevity, and crisp output. Always be sure the unit is turned off and unplugged before performing any cleaning procedures. 1. Use normal glass cleaner and a soft cloth to wipe down the outside casing. 2. Use a brush to wipe down the fan grill. 3. Whip down the colored bulb covers with a damp cloth to remove residue. 4. Always be sure to dry all parts completely before plugging the unit back in. ©American DJ Supply® - - Fire Bowl™ Instruction Manual Page 5 Fire Bowl™ Lamp & Fuse Replacement Caution: Always replace with the exact same type lamp and fuse, unless otherwise specified by an authorized American DJ® technician. Replace with anything other than the specified part can damage your unit and will void your manufactures warranty. Warning: If after you have replaced the lamp or fuse and you continue to blow either one, STOP using the unit. Contact customer support for further instructions, you may have to return the unit for servicing. Continuing to use the unit may cause serious damage. Fuse Replacement: Disconnect the unit’s main power supply. Insert a standard flat head screw driver in to the fuse holder housing located on inner plate of the unit. Turn the screwdriver in counter-clockwise direction to unlock the fuse holder. Remove the fuse holder to expose the fuse. Remove the old fuse and discard it. Replace the fuse with the same type. Insert the fuse holder back into it’s housing and turn it in clockwise direction to lock the holder back in to place. Lamp Replacement: Caution! Never attempt to change the lamps while the fixture is plugged in. Always disconnect the main power and allow the unit ample time to cool before attempting to replace the lamp. 1. Be sure to follow the proper procedures when handling halogen lamps. Never touch the new lamp with your bare fingers. 2. Carefully pull the lamp out of the socket and discard it. 3. Replace the lamp with an exact match. 4. If necessary adjust the position of the lamps. Fire Bowl™ Warranty Registration The Fire Bowl™ carries a 90 day limited warranty. Please fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number...