Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
10 Thank you for purchasing this American DJ® product. The Q-2221/X Is ready to be used, there Is no assembly required. Please read the following Instructions before installing or using your new unit. The Q-2221/X has a 2 year limited warranty! CAUTION! - Keep this device away from rain and moisture! Safety Instructions Always plug in the power last. Make sure that the Power switch is set to the OFF position before connecting other devices to the mixer. Keep away from heaters and other heating sources! If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch on the mixer immediately. The arising condensation of water might damage your device. Leave the device switched off until it has reached room temperature. Never put any liquids on the mixer or close to it. Should any liquid enter the device, disconnect from main power immediately. Have the device checked by a qualified service technician before operating again. Any damage caused by liquid entering the device is not subject to warranty! Never let the AC cord come in contact with other cables! Handle the AC cord and all AC connections with particular care. Make sure that the available voltage is not higher than stated on the AC voltage selector. Before the device is switched on, all fader and volume controls should be set to 0 or minimum position. Damages caused by manual modifications to the device or unauthorized operation by unqualified persons are not subject to warranty. There are no user serviceable parts inside the mixer. For maintenance and/or service, contact an authorized American DJ® dealer. ©American DJ Supply® - - Q-2221/X User Instructions page 3 Operating Determinations When installing this mixer, please make sure that the device is not exposed to extreme heat, moisture or dust! There should not be any cables lying around. Doing so endangers you as well as others. Do not operate the mixer in extremely hot (more than 30° / 100°F) or extremely cold (less than 5°C / 40°F) surroundings. Keep away from direct sunlight and heaters. Operate the mixer only after becoming familiar with its functions. Do not permit operation by persons not qualified for operating the mixer. Most damages are the result of unprofessional operation! Never use spray cleaners to clean the faders! Never use solvents or abrasive detergents to clean the mixer! It is recommended that you use a soft damp cloth. Please consider that unauthorized modifications on the device are forbidden due to safety reasons! Connections (Refer to diagrams on pages 5 & 7) • Make sure that the power switch is set to OFF. Before connecting other devices to the mixer, all units have to be switched off and the Master Control set to min. • Make sure that the available voltage is not higher than stated on the voltage selector before connecting to power. • In order to obtain the highest sound quality, only use high quality American DJ®, Ameri-Cable ™ cables for connecting devices. Make sure that the cables are properly fixed. • Connect your amplifier to the MASTER OUT jacks. Make sure that the channels are set properly. • For recording, connect your tape recorder or cassette deck to the OUTPUT REC jacks. The REC OUT level will not be influenced by the Master Control. • Connect your microphone to the Microphone Input on the rear panel. • The Q-2221/X features one microphone input. The 1/4 inch (6.3mm) MIC JACK on the rear panel. You can adjust the microphone volume output by turning the dJ MIC LEVEL. DJ MIC TREBLE & BASS may be controlled by the BaSS & TREBLE KNOBS below the DJ MIC KNOB. • You can connect 2 turntables using the LEFT & RIGHT RCA PHONO 1 and PHONO 2 jacks on the rear panel. You can only control the turntables signal after you have switched the PHONO /AUX SELECTOR SWITCH on the rear panel to PHONO, plus you must change the PHONO/AUX/LINE SWITCH on the front panel to PHONO/AUX. The signal is then controlled via the CH-1 and CH-2 faders. • Connect your tape recorder, tuner, sound effects, CD player, and cassette decks etc. to the LEFT & RIGHT RCA LINE signals to the AMP OUT jacks on the rear panel. The signal is then controlled via the CH-1 and CH-2 faders when the PHONO/AUX/LINE SWITCH on the front panel to LINE . CD players, cassette decks etc. may also be connected to the LEFT & RIGHT RCA PHONO/AUX jacks on the rear of the unit. You can only control this signal after you have switched the PHONO / AUX SELECTOR SWITCH on the rear panel to AUX, plus you must change the PHONO/AUX/LINE SWITCH on the front panel to PHONO/AUX. The signal is then controlled via the CH-1 and CH-2 faders. ©American DJ Supply® - - Q-2221/X User Instructions page 4 Front Panel - Functions and Controls 1. FEATHER FADER PLUS™ CROSSFADER - Mixes the signals of channel 1 and channel 2. When the crossfader is set in the center position, both channels can be heard at once. 2. HAMSTER SWITCH - Changes t...
Эта инструкция также подходит к моделям:Музыкальные инструменты - Q-2221/X (1.26 mb)