Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
Electric guitars have added “bite”, “chunk” and improved definition. As Guitar Player magazine said, “BBE is the most cost effective improvement you can add to your rig”. Acoustic guitars processed with the 362XL have a breathtakingly natural sparkle and presence. Bassists will delight in the BBE 362XL's ability to bring much more punch to the bottom end without muddying up the midrange. The 362XL is also great for keyboard rigs, with everything from the latest samples to a vintage Rhodes benefiting equally from the patented BBE process. Recording Systems The BBE 362XL can be used as an effect on individual tracks or applied overall during mixdown. The BBE process works very well to liven up the final mix, which is why the BBE 362XL and 882 models are popular for use in both recreational and professional recording studios. FRONT PANEL CONTROLS 1 2 3 4 5 1. CLIP LED: Will illuminate at +14dBu, giving a 6dBu warning of the impending distortion at +16dBu, the actual clip point. 2. LO CONTOUR: Regulates the amount of phase corrected bass frequencies. 3. PROCESS: Regulates the amount of phase corrected treble frequencies. 4. BBE FUNCTION: This push button switch allows for quick comparison of processed with unprocessed sound. When the switch is pushed in, the process is on and the indicator LED is green. When the switch is out, the process is off and the indicator LED is red. 5. POWER: This switch controls primary power to the BBE 362XL. REAR PANEL CONNECTIONS 1 2 3 4 3. OUTPUT: The output of the BBE 362XL can be taken from the 1/4” stereo TRS Phone Jack or the XLR Jack. Both are balanced and the same point electronically. This allows both outputs to be used simultaneously, eliminating the need for a “Y” cord in the event multiple, balanced outputs are required. The recommended single load impedance is at least 10k Ohms. If both outputs are being used, a minimum of a 22k Ohm load per device is required. (The “load” is determined by the input impedance of the next subsequent component in the signal chain.) The maximum output is rated at +26dBu. Pin #2 is considered the hot or “+” signal. The output impedance of the BBE 362XL is 600 ohms. NOTE: Actual output level will vary due to the selected position of the BBE Process, and the actual input signal level. If both the XLR and Phone Jacks are being used, both must be either balanced or unbalanced. Otherwise a loss of signal level will occur. 4. INPUT: The input of the BBE 362XL is a balanced connection. Although is can be either a TRS 1/4” stereo Phone Plug or an XLR Plug, it is recommended that only one input source be used. Both jacks are the same point electronically, however, due to the input/output impedance characteristics of most audio devices, a loss of signal may occur and/or damage to a component if both inputs are utilized. Pin #2 is considered the hot or “+” signal. The input impedance of th BBE 362XL is 10k Ohms. The maximum signal level is +26dBu. Specifications Frequency Response, process mode:……………………………Program controlled bypass mode: ……………………………5Hz to 30kHz Signal to noise ratio (balanced): ……………114dB Process in, 126dB Process out THD: ………………………………………………less than 0.1% at -10dBu input, Process in/out Maximum Input:…………………………………+18dBu (may vary due to control settings) Input Impedance: ………………………………10k Ohms Nominal Input Level: …………………………-10dBu ~ +4dBu Output Impedance: ……………………………600 Ohms Nominal Output Level: …………………………-10dBu ~ +4dBu Maximum Output Level: ………………………+20dBu unbalanced, +26dBu balanced * 0dBu = 0.775mVrms Terminations/Connections (Rear Panel): …XLR/1/4” TRS Phone Jacks Power Requirements: ……………………………U.S.model: 100-120VAC, 50/60Hz, 10 WATTS All other models: 200-240VAC, 50/60Hz, 10 WATTS Fuse: ………………………………………………Replace with the same type FASTBLOW fuse U.S. model: 250Vac, 1 /2A Fast blow type fuse. All other models: 250Vac, .125A Fastblow type fuse Dimensions: …………………………………...... Standard 1U single rack space, 19"(W) x 5.75"(D) x 1.7"(H) Shipping Weight: ………………………………4.5 lbs. (2.5kgs) Note: Due to continuing product improvement, specifications and design are subject to change without notice. General Operation THE BBE 362XL IS A LINE LEVEL SIGNAL PROCESSOR AND IS TO BE CONNECTED PRIOR TO THE POWER AMP IN ANY AUDIO SYSTEM. SIGNIFICANT DAMAGE MAY BE INFLICTED TO THE BBE 362XL OR ANY SUBSEQUENT COMPONENT IN THE SYSTEM IN THE EVENT THE OUTPUT OF A POWER AMP IS CONNECTED DIRECTLY TO THE INPUT OF THE BBE 362XL. In order to reduce the risk of damage to any equipment, properly connect all cables and power cables before turning on any components in the system. Most important of all, ALWAYS TURN ON THE POWER AMPLIFIER LAST TO AVOID DAMAGING THE SPEAKERS OR THE AMP. The BBE 362XL may be utilized in a number of different environments and its results may vary accordingly. Because both channels are completely independent from each other, only one channel of the BBE 362XL may be used, or each channel processing a different signal source. The effects loop ...