Оценок - 5, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
The amplifier’s internal speaker is disconnected when this jack is used. 15. Power Switch: This dual-function component is both an On/Off power switch and a status indicator light. When illuminated, it shows that your amplifier is ready to be played. To turn amplifier on, press switch upward. To turn amp off, press switch downward. kustom.com KG100FX112 Back Panel External Speaker: This is a two-conductor, .-inch external speaker jack. (Note: This jack is wired in series with the amp’s internal speaker. Therefore, the internal speaker still functions when an external speaker cabinet is added.) Footswitch: This amplifier provides foot-switchable channels and a “hidden” volume boost feature that works on either channel to help make solos stand out in the mix. These features may be accessed in the following ways: 1) By connecting a single-function footswitch with a stereo cable to the Footswitch jack on the amplifier’s back panel, users may change channels on the amp while playing. The boost feature will not be active. If a single-function footswitch is used with a mono cable, such as a guitar cable, users may still change channels on the amp while playing, but the boost feature will always be active. Kustom offers the model KACFS-100 single-function footswitch which comes with a stereo cable. It may be ordered from a Kustom dealer. 2) By connecting a dual-function footswitch, both channel-switching and the boost feature may be activated. The Kustom KACFS201 dual-function footswitch will switch channels and activate the boost function. It may be ordered from a Kustom dealer. Note 1: On the KACFS201 footswitch, channel-switching is labeled “Channel” and boost is labeled “Effect.” Note 2: When no footswitch is attached to the amplifier, the “hidden boost” feature is not active. Effects Loop Send: Use this 2-conductor, .-inch jack to connect to the input of an external effects processor or equalizer. This jack can also be used as a Preamp Out. Effects Loop Return: Use this 2-conductor, .-inch jack to connect to the output of an external effects processor or equalizer. This jack can also be used as a Power Amp In. (Note: This jack separates the preamp from the power amp. If using an external effect, the effect will be in series between the Effects Loop Send and Effects Loop Return. The amount of “dry” signal will be controlled by the external effect.) KG100FX112 AC Mains 1. AC Power Cord Receptacle: AC power cord can be removed for easy storage and replacement if damaged. Insert the AC cord (provided) firmly into the AC receptacle. NOTE: Replace the AC power cord if protective jacket is damaged or ground pin is damaged or removed. 2. Fuse: The fuse is located in a fuse tray just below the receptacle. Replace only with the same type and size. For your convenience, a spare fuse is located inside the fuse tray toward the front. To replace fuse, remove AC power cord. Remove fuse tray by pulling the tab located above the fuse symbol away from the receptacle. kustom.com KG100FX112 Suggested Settings The following suggested settings will help you dial in a variety of popular tones. Keep in mind, these are starting points to get you up and running with your KG amplifier. Feel free to experiment to achieve your own signature sounds. CLEAN GUITAR These settings are for punchy clean tones that are commonly used in Pop, Country, Alternative and many other genres of music. Use the Rhythm channel with the tone controls set to emphasize brighter sounds. The Bass control should be adjusted to maintain the clarity of the overall tone. Add Reverb and Chorus as desired. MEDIUM-GAIN GUITAR These settings are appropriate for Rock, Blues or other music styles that require a moderate amount of distortion. Use the Lead channel with the Gain set to its middle ranges. Likewise, keep the Mid control in its middle ranges but increase the amount of Treble to maintain clarity. HIGH-GAIN GUITAR Try these setting ranges when you want to produce the heaviest tones. Notice that the Gain control is cranked up, the amount of Bass is increased and Midrange is reduced for a heavy, modern vibe. Experiment by adding a bit of Delay to high-gain solos. kustom.com Kustom® KG100FX112 Specifications Output Power 100 Watts RMS 4 Ohms at 5% THD Speaker 1 x 12” 100 Watt 4 Ohm Special Design Input Impedance 470K Hum & Noise -56dB Residual noise, all level controls 0% (minimum) Lead Gain 96 dB Lead Gain and Volume controls full 70 dB Lead Gain and Volume controls half way Clean Gain 60 dB Clean volume control full 45 dB Clean volume control halfway Nominal Signal to Noise 75 dB Volumes and Gain halfway Footswitch Kustom KACFS-100 / KACFS-201 See Footswitch text in Back Panel description Effects 4 selectable digital effects Reverb, Delay, Chorus/Reverb, Chorus/ Delay Power Requirements USA/Canada 120VAC/60Hz, 180W Europe 230VAC/50Hz, 180W UK 230VAC/50Hz, 180W Australia 240VAC/50Hz, 180W Japan 100VAC/50-60Hz, 180W Dimensions/Weight mm/Kilogram 481 (Height) X 531 (W...