Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. kustom.com ENGLISH kustom.com FRENCH KXB200H/HR Control Panel 1 2 3 4 6 7 85 109 11 1312 KXB200 1. 0 dB Input: .-inch input that is intended for bass guitars with standard, passive electronics. 2. –6 dB Input: .-inch input that is optimized for bass guitars with active electronics. 3. Gain: Controls the input level to the preamp. Set so Clip indicator light is not lit, otherwise distortion may occur. 4. Volume: Controls the overall volume level of the amplifier. Use in conjunction with the Gain control to obtain the desired level. 5. EQ-63: This active control adjusts the low frequencies to boost or cut by 12 dB centered at approximately 63 Hz. 6. EQ-150: This active control adjusts the low-mid frequencies to boost or cut by 12 dB centered at approximately 150 Hz. 7. EQ-350: This active control adjusts the low-mid frequencies to boost or cut by 12 dB centered at approximately 350 Hz. 8. EQ-800: This active control adjusts the hi-mid frequencies to boost or cut by 12 dB centered at approximately 800 Hz. 9. EQ-2K: This active control adjusts the high frequencies to boost or cut by 12 dB centered at approximately 2 kHz. 10. EQ-5K: This active control adjusts the high frequencies to boost or cut by 12 dB centered at approximately 5 kHz. 11. Aux In: This is a 3-conductor, 1/8-inch, stereo jack that allows playback from a Compact Disc, MP3 player or other audio device. The overall volume level will be determined by the audio device, so start with lower volume levels and increase as needed. 12. Headphones: This is a 3-conductor, 1/8-inch input jack intended for headphone use. The amplifier’s internal speaker is disconnected when this jack is used. 13. Power Switch: This dual-function component is both an On/Off power switch and a status indicator light. When illuminated, it shows that your amplifier is ready to be played. To turn amplifier on, press switch upward. To turn amp off, press switch downward. kustom.com KXB200H/HR Back Panel /KXB200H HR Speaker Outputs: These are two-conductor, .-inch external speaker jacks. These jacks are wired in a parallel configuration. Use them to connect the amplifier head to speaker cabinets with a minimum total impedance of 4 ohms. (Note: Be sure that the amp is turned off before connecting or disconnecting speaker cabinets.) Examples: If you have two 8-ohm speaker cabinets and plug one into each of the amplifier’s two speaker jacks, the total load will be 4 ohms. Because this is equal to the minimum-rated load for the amplifier (4 ohms), this combination is acceptable. If you have two 4-ohm speaker cabinets and plug one into each of the amplifier’s two speaker jacks, the total load will be 2 ohms. Because this is below the minimum-rated load of the amplifier (4 ohms), this combination must not be used. Effects Loop Send: Use this 2-conductor, .-inch jack to connect to the input of an external effects processor or equalizer. This jack can also be used as a Preamp Out. Effects Loop Return: Use this 2-conductor, .-inch jack to connect to the output of an external effects processor or equalizer. This jack can also be used as a Power Amp In. Balanced Line Out: This XLR jack is used to connect the amplifier to a mixer or other line level amplifier. (Note: This output is post-EQ and post- Effects Loop but is located before the Volume control.) Direct Out Volume: This control sets the output level for the Balanced Line Out. Set in its lower ranges until necessary volume has been determined. Ground Lift: Activating this switch removes the ground connection on the Balanced Line Out jack. If necessary, use this switch to eliminate hum. kustom.com KXB200H/HR AC Mains kustom.com KXB200H/HR Suggested Settings The following suggested settings will help you dial in a variety of popular tones. Keep in mind, these are starting points to get you up and running with your KXB amplifier. Feel free to experiment to achieve your own signature sounds. KXB200 TRADITIONAL/VERSATILE TONE In this setting, the amplifier will deliver a traditional, yet versatile, electric bass sound. Whether you are playing Rock, Country, Blues or Gospel, this setting will get you close. If you play with a pick and want less treble attack on the notes, decrease the amount of high frequencies using the 2K and 5K controls. If you need a deeper bottom end, increase the amount of low frequencies using the 63 control. Adjust the amount of Low and High Midrange to best match the tone of your bass guitar and how it fits into the overall sound. KXB200 FUNKY, SLAPPED TONES This style of music needs a strong attack with lots of treble. Using less Low-mids will help produce the extra top end necessary for this type of music. If you use a “slapping” thumb technique, add a bit more low end and extra volume – or less if you really hit the strings hard. KXB200 ALTE...