Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
For that reason, we recommend that it be powered with the supplied AC power adaptor for normal use. Always turn the PHONES ON/OFF switch OFF before making AC power connections or replacing the battery. ¦ Supplying AC Power 1. Plug the adaptor’s DC output cable into the Silent Guitar’s DC IN jack, making sure the plug is firmly inserted into the jack. 2. Plug the AC adaptor into a convenient wall AC power socket. • Battery power is automatically disconnected when the AC adaptor is connected. • When the AC adaptor is used, the batteries may leak.To prevent leakage we recommend that you remove the batteries from the instrument. When the AC adapter is used. • When using an AC adaptor, make sure you use only one of the following recommended adaptors (Recommended Adaptors: PA-D09, PA-1E, PA-3C). The use of any other adaptor may result in damage to the instrument or cause fire, etc. Please use with caution. ¦ Installing the Battery and place it in the battery case. Take careful note of the polarity markings (+/-) as shown in the illustration when connecting the battery. (Reversed polarity may damage the circuit.) 4. Close the battery compartment cover. 1. Be sure to use a 9-volt alkaline battery 6LR61. (not supplied) • When using a battery, please use an alkaline battery. Use of a manganese battery will result in an extremely shorter battery life depending upon the type of battery used. 2. Remove the battery compartment cover, located on the back side of the Silent Guitar, by sliding the tab labeled “OPEN” toward the head of the guitar. 3. Attach the 9-volt battery 6LR61 to the battery snap, 6LR61 9V Alkaline battery Battery compartment cover Battery snap Bij dit produkt zijn batterijen geleverd. Wanneer deze leeg zijn, moet u ze niet weggooien maar inleveren als KCA. * For customers in Netherlands When battery power becomes low, the reverb will no longer operate, the lamp will not light and noise will be present. Replace the battery with a new alkaline battery as soon as possible. • Always follow the +/– signs when inserting the battery. Improper insertion may result in fire. • To prevent possible damage to the unit due to battery leakage and unnecessary power drain, remove the battery from the unit when it is not going to be used for an extended period of time. Using the Controls ¦ Using the LINE OUT jack (Using with a guitar amplifier or powered speaker, etc.) 1. Use a standard phone plug cable to connect the Silent Guitar’s LINE OUT jack to the input jack on the guitar amplifier or powered speaker, etc. When the cable’s plug is inserted into the LINE OUT jack, power will be supplied to the Silent Guitar and the power lamp will light. • Before making any connections, make sure that the output volume on the guitar amplifier or powered speaker, etc., is turned down or its power is switched OFF. • When the guitar is not being used, disconnect the cable’s plug to save battery. 2. Rotate the VOLUME knob while playing, and adjust the volume to a suitable level. • If the sound is distorted when playing vigorously, turn the VOLUME knob slightly to the left. 3. Rotate the BASS and TREBLE control knobs to adjust the sound quality. Rotate the BASS knob to the right to increase the low frequencies, and to the left to decrease the low frequencies. Rotate the TREBLE knob to the right to increase the high frequencies, and to the left to decrease the high frequencies. 4. The REVERB function can be used for adding reverb to the guitar’s tone to produce the live acoustic characteristics experienced in a room or hall. Set the REVERB switch to its “1” position to add the type of reverb usually experienced in a room, or set the switch to its “2” position to add the type of reverb normally experienced in a hall. • When compared to the REVERB switch’s REVERB 1 or REVERB 2 positions, the instrument consumes less power when the REVERB switch is in its OFF position. • Some noise is produced when the position of the REVERB switch is changed. When the power is Adjusts the Adjusts low Adjusts high ON, the lamp lights. volume frequencies frequencies OFF 1 2 OFF ON PHONESREVERB VOLUME BASS TREBLE ¦ Using the stereo earphones (or stereo output to an external device) When using the instrument with the supplied stereo earphones or a separately purchased pair of headphones, or when you want to send the instrument’s stereo output to an external device, use the headphones (PHONES) jack for connecting the earphones or external device. 1. Set the headphones ON/OFF switch, located on the right side of the control panel, to its “ON” position to supply power to the Silent Guitar. The power lamp will light. 2. Insert the earphone plug into the headphone jack. When connecting the instrument to an external device, connect the external device to the PHONES jack using a cable with a stereo plug. 3. The remaining procedures are the same as described above in the “Using the LINE OUT jack” section’s steps 2 through 4. • When using a pair of headphones, do not ...
Эта инструкция также подходит к моделям:Музыкальные инструменты - SLG100S (313.31 kb)