Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
The MFC06 offers convenient foot control of the Yamaha FX500 SIMUL-EFFECT PROCESSOR: direct footswitch selection of up to 5 different effect programs and ON/OFF switching of the COMPRESSOR, DISTORTION, EQ, MODULATION and REVERB stages. The MFC06 is built to Yamaha's rigid quality standards, and will provide reliable service for many years if handled properly. Please read this operation manual thoroughly before setting up and using your MFC06. PRECAUTIONS 1. AVOID EXCESSIVE HEAT, HUMIDITY, DUST AND VIBRATION Keep the unit away from locations where it is likely to be exposed to high temperatures or humidity — such as near radiators, stoves, etc. Also avoid locations which are subject to excessive dust accumulation or vibration which could cause mechanical damage. 2. AVOID PHYSICAL SHOCKS Strong physical shocks to the unit can cause damage. Handle it with care. 3. DO NOT OPEN THE CASE OR ATTEMPT REPAIRS OR MODIFICATIONS YOURSELF This product contains no user-serviceable parts. Refer all maintenance to qualified Yamaha service personnel. Opening the case and/or tampering with the internal circuitry will void the warranty. 4. HANDLE CABLES CAREFULLY Always plug and unplug cables by gripping the connector, not the cord. 5. CLEAN WITH A SOFT DRY CLOTH Never use solvents such as benzine or thinner to clean the unit. Wipe clean with a soft, dry cloth. 6. ALWAYS USE THE CORRECT POWER SOURCE The MFC06 will run from dry batteries or an optional AC adaptor. Use ONLY the Yamaha PA-1 or PA-1 B AC adaptor when running the MFC06 from the AC mains. Attempting to use other AC adaptors can cause serious damage. 7. ELECTRICAL INTERFERENCE The MFC06 contains digital circuitry, and may cause interference if placed top close to television or radio receivers, or other broadcast reception equipment. If interference occurs, move the MFC06 further away from the affected equipment. 8. IF YOU WON'T BE USING THE MFC06 FOR A WHILE If your MFC06 will not be used for an extended period of time, remove the internal batteries. The AC adaptor should be unplugged from the AC mains outlet whenever the MFC06 is not being used. 9. MIDI CABLE Always use the MFC06 with a properly constructed MIDI cable. Never use a MIDI cable longer than 15 meters. BATTERY INSTALLATION The MFC06 requires 6 "AA" type dry batteries if you intend to operate it without the PA-1 or PA-1 B AC adapter. Alkaline type dry batteries are recommended because of their longer life. 0 Make sure the MFC06 power switch is OFF. (2) Use a coin or similar object to turn the large screw retaining the battery compartment cover on the bottom panel of the MFC06, and remove the battery compartment cover. (3) Remove the battery holder, taking care not to pull on or damage the battery wires. Unsnap the battery holder from the battery clip. © Install the six batteries in the battery holder, making sure that each battery faces in the proper direction. Battery orientation markings are provided on the battery holder. (5) Snap the battery clip securely back onto the battery holder, and replace the battery holder in the battery compartment. (6) Replace the battery compartment cover and tighten the retaining screw. * When the batteries need replacing, the MFC06 indicators will begin to flash. When this happens, replace all six batteries at the same time. New batteries should never be mixed with old ones. * When performing, it’s a good idea to have a spare set of batteries handy— just in case. * It is a good idea to have a fresh set of batteries installed even when using the PA-1 AC adapter. If the AC adapter cord is accidentally unplugged during use, the MFC06 will instantly switch to battery power. * Even when no batteries are installed, make sure to attach the battery clip to the battery holder. If this is not done, the battery clip can come in contact with a conducting surface inside the battery compartment, thus shorting the power supply and possible causing damage. SETTING UP Please set up the MFC06 according to the following procedure. 0 Install the batteries as described in the previous section, or connect a Yamaha PA-1 or PA-1 B AC Adapter to the DC 9-12VIN jack. If batteries are installed and the AC adapter cable is connected to the MFC06, the batteries are automatically disconnected and the AC adapter provides power to the MFC06. © After making sure that both the MFC06 power switch and the FX500 power switch are OFF, connect an appropriate MIDI cable (less than 15 meters) from the MFC06 MIDI OUT connector to the MIDI IN connector on the FX500. (3) First turn the MFC06 power switch ON, and then the power switch of the FX500. When the MFC06 power switch is turned ON, the "PGM" LED indicator will light. t n U YAMAHA < )o Г1-1_Г 1—I“1—J—1_1-1_f i_Í 1 1 1 (D © Set the receive channel of the FX500 "BANK" (A, B, C or D) you intend to use to "1" or "OMNI." Refer to your FX500 operation manual for details. The MFC06 transmits only on channel 1. (5) Sin...