Оценок - , средний балл:
(
)
)
Производитель: Yamaha
Размер: 1.82 mb
Название файла:
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
К этому устройству также есть другие инструкции:
Музыкальные инструменты - AUDIOGRAM6 (286.33 kb)
Музыкальные инструменты - AUDIOGRAM6 (300.07 kb)
Фрагмент инструкции
Click the “Register Now” button shown when the software is started, then fill in all required fields for registration. If you do not register the product, you will be unable to use the application after a limited period of time expires. • To install on Mac computers double-click the “Cubase AI*.mpkg” icon or the “Cubase AI* Start Center” icon. “*” indicates where the version number appears in the actual icon name. • Visit the web address below for the latest information on: <1 Turn all gear that is to be connected to the AUDIOGRAM off or to standby mode (except the computer), and set the LEVEL controls, MASTER LEVEL control and DAW control to their minimum settings. 2 Connect microphones and/or instruments. For details on making connections refer to the “Setup” section on page 7 and the “Controls and Functions” section on page 15. 3 Set the MIC/INST switch according to the type of device connected to channel 1 or 2. Select MIC ( ) if a microphone is connected, or INST ( ) if a guitar or similar instrument is connected. 4 To use channels 1 and 2 as independent mono channels set the MONO/STEREO switch to MONO ( ). To use channels 1 and 2 as a stereo pair set the switch to STEREO ( ). Step 1 Installing Cubase AI Step 2 Connecting to the AUDIOGRAM interface Important! NOTE LEVEL controls MASTER LEVEL control DAW control Be sure to turn the PHANTOM +48V switch on when using a phantompowered condenser microphone. Quick Guide AUDIOGRAM 6 Owner’s Manual 9 To prevent loud pops and noises, turn on the power to your sound gear starting with the sources (instruments, CD players, etc.) and ending with the monitor speakers (powered speakers). 1 Turn on the instruments and microphones. 2 If you are using a condenser microphone for the channel 1, turn on the PHANTOM +48V switch. Observe the following precautions when turning on phantom power. • Make sure that the PHANTOM +48V switch is off when phantom power is not needed. • When turning the switch on, be sure that only a condenser microphone is con- nected to the channel 1 MIC/INST input jack. Other devices may be damaged if connected to phantom power. This precau- tion does not apply to balanced dynamic microphones or instruments with the phone jack, however, as these will not be affected by phantom power. •To prevent damage to speakers, be sure to turn off power amplifiers (or powered speakers) before turning this switch on or off. We also recommend that you set the MASTER LEVEL control to the minimum position before operating this switch to avoid the risk of loud noises that could cause hearing loss or device damage. 3 Connect the AUDIOGRAM interface to your computer using the supplied USB cable. The POWER indicator will light to indicate that power is being applied to the AUDIOGRAM interface. When connecting or disconnecting the USB cable be sure to turn the DAW control and the MASTER LEVEL control all the way down. The first time you connect to the computer’s USB connector, or change the connection to a different USB port, a driver installation dis- play may appear. If this occurs, wait until the installation is complete before proceeding. 4 Turn the power to the monitor speakers (powered-speakers). 1 Set the GAIN controls to the minimum position and the LEVEL controls to about 1 o’clock. Set the MASTER LEVEL control to the mini- mum position. Failure to do so may result in loud noise bursts that can damage your equipment, your ears, or both. 2 Adjust the volume on all instruments that are connected to the AUDIOGRAM interface. 3 Adjust the channel GAIN controls so that the corresponding PEAK indicators flash briefly on the highest peak levels. 4 Adjust the overall volume with the MASTER LEVEL control while monitoring via head- phones or monitor speakers. Lower the volume using the LEVEL controls until the level indicator PEAK LEDs flash only briefly on occa- sional high-level peaks or not at all. Step 3 Powering Up the System CAUTION USB Connection Precautions Be sure to observe the following points when connect- ing to the computer's USB interface. Failure to observe these rules can result in computer freezes/hang-ups and possibly data loss or corruption. If the instrument or computer does hang up, restart the application or computer. • Be sure to wake the computer from sleep/ suspended/standby mode before making a connection to the computer’s USB connec- tor. •Always quit all applications running on the computer before connecting or disconnect- ing the USB cable. •Wait at least 6 seconds between connecting or disconnecting the USB cable. CAUTION CAUTION NOTE Step 4 Adjusting Level CAUTION GAIN controls LEVEL controls PEAK indicators MASTER LEVEL control DAW control Level indicator Quick Guide 10 AUDIOGRAM 6 Owner’s Manual Cubase AI Setup 1 Set the computer output to the maximum level. For details on how to make the setting refer to the “The recorded sound is too low in level.” section in the “ Quick Guide 10 AUDIOGRAM 6 Owner’s Manual C...