Производитель: Yamaha Размер: 2.46 mb Название файла: Язык инструкции:

Перейти к скачиванию

2 3 . Snare pad 1. Attach a clamp bolt to the snare pad and provisionally tighten (by five or six turns). 2. Push the snare pad onto the rack’s snare holder. Ensure that the snare holder’s rod is fully inserted into the snare pad’s mounting hole, and then tighten the clamp bolt to secure the pad in place. 3. Loosen bolts A to D as shown below to adjust the height and angle of the snare pad’s playing surface. When correctly positioned, be sure to securely retighten the bolts before proceeding to the next step. . Tom pads 1. As with the snare pad, attach a wing bolt (DTX532K) or clamp bolt (DTX562K) to each of the three tom pads and provisionally tighten (by five or six turns). 2. Push each of the tom pads onto one of the rack’s tom holders. Each time, ensure that the tom holder’s rod is fully inserted into the tom pad’s mounting hole, and then tighten the bolt to secure the pad in place. 3. Loosen bolts A to C as shown below to adjust the height and angle of each tom pad’s playing surface. When correctly positioned, be sure to securely retighten the bolts before proceeding to the next step. XP80 Snare Pad Tom pads DTX532K: TP70 DTX562K: XP70 Clamp bolt (tighten in the direction of the arrow) Underside of snare pad Push on Snare pad Snare holder Rod Clamp bolt Bolt A Bolt C Bolt D Bolt B Tom pad: TP70 Tom pad: XP70 .DTX532K .DTX562K Rod Push on Push on Wing bolt Tom holder Clamp bolt Tom holder Rod Bolt C Bolt B Bolt A *DTX562K shown. Assembling the snare and tom pads U.R.G., Digital Musical Instruments Division © 2013 Yamaha Corporation 211POAP*.*-01A0 Printed in Vietnam ZE16340 Continued on rear. . Drum module 1. Secure the module holder to the bottom of the drum module using the module holder screws. 2. Push the module holder into the holder clamp and tighten the clamp bolt to secure it in place. . Each cymbal pad 1. Using the tuning key, loosen the stopper’s key bolt. 2. Remove the wing nut, the two felt pads, and the bolt cover from the cymbal holder. 3. Place the stopper on the cymbal holder. * If the key bolt was not sufficiently loosened in Step 1 above, it may not be possible to pass the stopper over the cymbal holder’s shaft. In such a case, loosen the key bolt as much as possible without removing it. 4. Replace the bolt cover. * Turn the bolt cover to tighten it onto the threaded section and firmly secure it in place. 5. With the stopper making full contact with the bottom surface of the bolt cover as shown below, tighten the stopper’s key bolt using the tuning key. 6. Place one of the felt pads removed in Step 2 on the cymbal holder. 7. Mount the pad on the cymbal stand. Lower the pad into place with the cymbal holder’s shaft passing through the central hole. When mounted, the stopper’s pin should rest inside the pad’s smaller hole. * If you were to play your cymbal pad without the stopper’s pin positioned well inside the smaller hole, the pad could rotate, causing the cable to be pulled out. It is very important, therefore, to ensure that the stopper is secured as shown in Step 5 above. 8. Assemble the felt pad that came with the cymbal pad. 9. Tighten the wing nut to secure the pad to the cymbal holder. A cymbal pad’s built-in sensor is located close to the Yamaha logo found on the top surface. In order to achieve the best performance from your pad, position it such that the area around the logo can be easily struck. (See the figure above.) PCY135 Cymbal Pad Drum module PCY135 Cymbal Pad Module holder screws Module holder Bottom of drum module Front side Clamp bolt Drum module + module holder Push in Holder clamp Tuning key Key bolt Stopper Cymbal holder Felt pads Bolt cover Wing nut Cymbal holder Stopper Bolt cover Threaded section The second felt pad removed from the cymbal holder in Step 2 above is not required for assembly. Cymbal holder Stopper Bolt cover Full contact Felt pad that Cymbal pad came with cymbal Cymbal holder Felt pad Bolt cover Cymbal pad Stopper Pin Wing nut Stopper Smaller hole Assembling the drum module and cymbal pads 1. If a drum mat (sold separately) is not available, lay a sheet of cardboard on the floor to prevent it from being scratched. 2. Loosen the hi-hat stand’s wing bolt a. 3. Open up the three legs as shown below and then retighten the wing bolt a to lock them in place. 4. Insert the connecting rods into the holes in the frame as shown below. 5. As shown on the right, loosen the hi-hat clutch’s wing bolt b and remove the hi-hat clutch. * The hi-hat clutch is not required when assembling the electronic drum kit in the standard fashion described in this manual. Instead, the hi-hat clutch that came with the RHH135 Real Hi-Hat Pad will be used. 6. Remove the hi-hat shaft from the upper tube . 7. Insert the hi-hat shaft from Step 6 as far as it will go into the lower tube and screw in the tip. 8. Insert the upper tube over the hi-hat shaft and tighten the wing bolt c to secure it in place with the bottom seat approximately half way between the top of the lower tube ...

Эта инструкция также подходит к моделям:
Музыкальные инструменты - DTX562K (2.46 mb)

Скачать инструкцию

Чтобы скачать, введите 2 цифры: