Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
5 Check the radio button to the left of “Search for a suitable driver for my device. (Recommended).” Click [Next]. The window that appears enables you to select a location in which to install the driver. 6 Check the “CD-ROM drives” box and uncheck all other items. Click [Next]. NOTE • The system may ask you to insert a Windows CD-ROM while it checks for the driver. Specify the “USBdrv2k_” directory of the CDROM drive (such as D:\USBdrv2k_\) and continue the installation. 7 When the installation is complete, the system displays “Completing the Found New Hardware Wizard.” Click [Finish]. NOTE • Some computers may take about ten seconds to show this screen after the installation is complete. 8 Restart the computer. The driver has been installed. ¦ Installing the driver on Windows XP 1 Start the computer. 2 Select [Start] > [Control Panel]. If the control panel appears as “Pick a category”, click “Switch to Classic View” in the upper left of the window. All control panels and icons will be displayed. 3 Go to [System] > [Hardware] > [Driver Signing Options], and check the radio button to the left of “Ignore” and click [OK]. 4 Click the [OK] button to close System Properties, and then click “X” in the upper right of the window to close the Control Panel. 5 Insert the included CD-ROM into the CD-ROM drive. 6 First, make sure the POWER switch on the Tyros2 is set to OFF, then use a USB cable to connect the USB connector of the computer (or the USB hub) to the USB TO HOST connector of the Tyros2. When the instrument is turned on, the computer automatically displays the “Found New Hardware Wizard.” NOTE • Some computers may take a few minutes to show this screen. 7 Check the radio button to the left of “Install the software automatically. (Recommended).” Click [Next]. The system starts the installation. 8 When the installation is complete, the system displays “Completing the Found New Hardware Wizard.” Click [Finish]. NOTE • Some computers may take about a few minutes to show this screen after the installation is complete. 9 Restart the computer. The driver has been installed. Voice Editor Once you’ve installed the Voice Editor, you can use your computer to edit the voices of the Tyros2. 1 Double-click on the “VoiceEditor_” folder in the CD-ROM. The file “setup.exe” will be displayed. 2 Double-click on the “setup.exe” file. The setup dialog will be displayed. 3 Execute the installation by following the on-screen directions. For subsequent operations, refer to the PDF owner’s manual for the Voice Editor. English 4 Tyros2 Accessory CD-ROM Installation Guide Troubleshooting The driver cannot be installed. • Is the USB cable connected correctly? > Check the USB cable connection. > Disconnect the USB cable, then connect it again. • Is the USB function enabled on your computer? > When you connect the instrument to the computer for the first time, if the “Add New Hardware Wizard” does not appear, the USB function on the computer may be disabled Perform the following steps. 1 Select [Control Panel]* > [System] > [Hardware] > [Device Manager]. * Classic View only in Windows XP. 2 Make sure that no “!” or “x” marks appear at “Universal serial bus controller” or “USB Root Hub.” If you see an “!” or “x” mark, the USB controller is disabled. • Is any unknown device registered? > If driver installation fails, the instrument will be marked as an “Unknown device,” and you will not be able to install the driver. Delete the “Unknown device” by following the steps below. 1 Select [Control Panel]* > [System] > [Hardware] > [Device Manager]. * Classic View only in Windows XP. 2 Look for “Other devices” in the menu “View devices by type.” 3 If you find “Other devices,” double-click it to extend the tree to look for “Unknown device.” If one appears, select it and click the [Remove] button. 4 Remove the USB cable from the instrument, and make the connection again. 5 Install the driver again (page 4). When controlling the Tyros2 from your computer via USB, the Tyros2 does not operate correctly or no sound is heard. • Did you install the driver? • Is the USB cable connected correctly? • Are the volume settings of the Tyros2, playback device, and application program set to the appropr...