Оценок - 3, средний балл: 4
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
A microphone may sustain damage if connected to this jack. 18 MG32/14FX, MG24/14FX s L Rear Input/Output Block ¦ CHANNEL I/O Section 2 13 1 Monaural-Channel Input Jacks (MG32/14FX: CHs 1 to 24, MG24/14: CHs 1 to 16) • INPUT A These are balanced XLR input jacks. • INPUT B These are balanced phone input jacks. You can connect either balanced or unbalanced phone plugs to these jacks. NOTE On any given channel, you may use either INPUT A or INPUT B, but not both. If you connect to both of these inputs, only INPUT B will be effective. 2 INSERT I/O Jacks These are unbalanced TRS (tip, ring, sleeve) phone-type bidirectional jacks. You can use these jacks to connect channels to devices such as graphic equalizers, compressors, and noise filters. NOTE Connection to an INSERT I/O jack requires a special separately-sold insertion cable such as illustrated below. To the input jack of the external processor To the INSERT I/O jack To the output jack of the external processor Ring Sleeve Tip Sleeve Tip 3 Stereo-Channel Input Jacks (MG32/14FX: CHs 25/26, 27/28, 29/30, 31/32) (MG24/14FX: CHs 17/18, 19/20, 21/22, 23/24) • Phone jacks (MG32/14FX: CHs 25/26, 27/28, 29/30, 31/32) (MG24/14FX: CHs 17/18, 19/20, 21/22, 23/24) These are unbalanced phone input jacks. You can use each pair of jacks to input a stereo signal. Feed the L signal into the odd-numbered channel, and the R signal into the even-numbered channel. • RCA-pin jacks (MG32/14FX: CHs 29/30, 31/32) (MG24/14FX: CHs 21/22, 23/24) These are unbalanced RCA-pin input jacks. You can use each pair of jacks to input a stereo signal. Feed the L signal into the odd-numbered channel, and the R signal into the even-numbered channel. NOTE • Where a channel provides both a phone jack and an RCA pin jack, you may use either one of these jacks but you may not use both at the same time. Please connect to only of these jacks on each channel. • Some of the phone jacks (MG32/14FX: CHs 25/26, 27/28; MG24/14FX: CHs 17/18, 19/20) also support monaural input. Specifically, if you input only into the L (MONO) jack of either pair (while leaving the R jack empty), the mixer will propagate the same signal through both the L (MONO) and R inputs. MG32/14FX, MG24/14FX 19 s ¦ MASTER I/O Section B A 8 7 1 2345690C 1 RETURN Jacks (1, 2) These are unbalanced phone input jacks. The signal into each of these jacks feeds into the ST bus and into AUX buses 1 to 4. These jacks are typically used to receive a return signal from an external effector (reverb, delay, etc.). NOTE These jacks can also be used as an auxiliary stereo input. If you connect to the L (MONO) jack only, the mixer will recognize the signal as monaural and will propagate the identical signal from both L and R jacks. 2 2TR IN Jacks These unbalanced RCA-pin input jacks can be used to input a stereo sound source. The signal into each of these jacks feeds into the ST bus. Use these jacks when you want to connect a stereo sound source (such as a CD player or DAT deck) directly to the mixer for monitoring. 3 REC OUT (L, R) Jacks These are unbalanced RCA-pin output jacks. By connecting these jacks to an external recorder, you can record the same signal that is being output from the ST OUT jacks. NOTE The signal from these jacks is not adjusted by the ST master fader and is not affected by input or output at the INSERT I/O jacks. When using these jacks to record, adjust the level as necessary at the external recording device. 4 SEND Jacks •AUX Jacks (1 to 6) These are impedance-balanced phone jacks. These jacks output the signals from AUX1 to AUX6, respectively. You use these jacks, for example, to connect to a monitoring system, effector, or other such equipment. • EFFECT Jacks (1, 2) These impedance-balanced phone jacks output the signals from the EFFECT buses. You would typically use these jacks to connect to an external effector. 5 GROUP INS I/O Jacks (1 to 4) These are unbalanced TRS (tip, ring, sleeve) phone-type bidirectional jacks. You can use these jacks to connect individual groups to devices such as graphic equalizers, compressors, and noise filters. NOTE Connection to an INSERT I/O jack requires a special separately-sold insertion cable such as illustrated below. To the input jack of the external processor To the INSERT I/O jack To the output jack of the external processor Ring Sleeve Tip Sleeve Tip 6 GROUP OUT Jacks (1 to 4) These are impedance-balanced phone output jacks. These jacks output the signals from GROUP buses 1 to 4. Use these jacks to connect to the input jacks of MTRs, external mixers, and other such devices. 20 MG32/14FX, MG24/14FX s INPUT A, ST OUT, MONO Pin 1: Ground Pin 2: Hot (+) Pin 3: Cold (–) INPUT OUTPUT MIC (Talkback) Pin 1: Ground Pin 2: Hot (+) Pin 3: Ground INPUT INPUT B, GROUP OUT, AUX SEND (1 to 6), EFFECT SEND (1, 2), ST SUB OUT* Tip: Hot (+) Ring: Cold (–) Sleeve: Ground Ring Sleeve Tip INSERT I/O, GROUP INS I/O, ST INSERT I/O Tip: Output Ring: Input Sleeve: Ground PHONES Tip: L Ring: R Sleeve: Ground S...
Эта инструкция также подходит к моделям:Музыкальные инструменты - MG32/14FX (6.49 mb)