Оценок - 3, средний балл: 4
(
)
)
|
К этому устройству также есть другие инструкции:
Музыкальные инструменты - M3000-40C (116.01 kb)
Музыкальные инструменты - M3000-40C (114.47 kb)
Музыкальные инструменты - M3000-40C (114.48 kb)
Фрагмент инструкции
Tip (send) 1/4" phone plug Sleeve (ground) With the factory settings, the post-fader signal is output. However by changing internal jumpers, you can switch this so that the pre-EQ or pre-fader/post EQ signal is output. If you wish to change internal jumper settings, please contact your dealer. C INSERT I/O jacks These are TRS phone jacks which allow an external effect processor to be inserted into each mono input channel. Nominal level is 0 dB. Pin wiring is as follows. D INPUT A jacks These are XLR-3-31 type input jacks (balanced). Nominal input level is +10 dB ~ –30 dB. To use these jacks, you must set the A/B select switch of the corresponding stereo input channel to the A position. Pin wiring is as follows. 1 (ground) Male XLR plug 3 (cold) 2 (hot) E INPUT B jacks These are RCA phono input jacks (unbalanced). Nominal input level is +10 dB ~ –20 dB. To use these jacks, you must set the A/B select switch of the corresponding stereo input channel to the B position. Pin wiring is as follows. Phono plug Tip Sleeve Rear panel Rear panel s QNMLJ I GF 2–10dBV 1+4dB MASTER SLAVE VCA MASTER/SLAVE VCA EXTERNAL I/O CUE CONTROL IN OUT THRU MIDI 2TR IN MONITOR OUT+4dB MATRIX OUT+4dB MIX OUT +4dB ST INSERT I/O 0dB MATRIX SUB IN +4dB MIX INSERT I/O 0dB ST OUT+4dBCONTROL CUE SUB IN ST SUB IN MIX SUB IN +4dB +4dB +4dB R L R L 16 15 14 13 12 11 10 9 8 7 6 5 3 2 1 PHANTOM MASTER ON OFF L R L R L R L R 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 13 14 15 16 9 10 11 12 A B DC POWER INPUT R S U VT P O F MIX INSERT I/O jacks These are TRS phone jacks for inserting external signal processors into MIX buses 1–16. Nominal input/ output level is 0 dB. Pin wiring is as follows. Tip (send) 1/4" phone plug 1/4" phone plug 1/4" TRS phone plug To processor’s input From processor’s output Connect to INSERT I/O jack Tip (send) Ring (return) Sleeve (ground) Sleeve (ground) Tip (return) Sleeve (ground) G STEREO INSERT I/O jacks These are TRS phone jacks for inserting external signal processors into the ST bus. Nominal input/output level is 0 dB. Pin wiring is as follows. Tip (send) 1/4" phone plug 1/4" phone plug 1/4" TRS phone plug To processor’s input From processor’s output Connect to INSERT I/O jack Tip (send) Ring (return) Sleeve (ground) Sleeve (ground) Tip (return) Sleeve (ground) H MATRIX SUB IN jacks These are 1/4" phone jacks (unbalanced) for mixing the signals of external devices into matrix 1–8. Nominal input level is +4 dB. Pin wiring is as follows. Tip (send) 1/4" phone plug Sleeve (ground) KH I MIX OUT jacks These are XLR-3-32 output jacks (balanced) for individually outputting the signals of MIX buses 1–16. Nominal output level is +4 dB. Pin wiring is as follows. 2 (hot) Female XLR plug 3 (cold) 1 (ground) J MATRIX OUT jacks These are XLR-3-32 output jacks (balanced) for individually outputting the signals of matrix 1–8. Nominal output level is +4 dB. Pin wiring is as follows. 2 (hot) Female XLR plug 3 (cold) 1 (ground) K MIX SUB IN jacks These are 1/4" phone jacks (unbalanced) for individually mixing signals from external devices into MIX buses 1–16. Nominal output level is +4 dB. Pin wiring is as follows. Tip (send) 1/4" phone plug Sleeve (ground) Rear panel Rear panel 2 (hot) Female XLR plug 3 (cold) 1 (ground) M MONITOR OUT jacks These are XLR output jacks (balanced) for monitoring the monitor source selected on the control panel. Nominal output level is +4 dB. Pin wiring is as follows. 2 (hot) Female XLR plug 3 (cold) 1 (ground) N 2TR IN jacks These jacks are for connecting line-level external devices. l 2TR IN 1 jacks These are XLR balanced input jacks. Nominal input level is +4 dB. Pin wiring is as follows. 1 (ground) Male XLR plug 3 (cold) 2 (hot) l TR IN 2 jacks These are 1/4" phone unbalanced input jacks. Nominal input level is –10 dBV. Pin wiring is as follows. Tip (send) 1/4" phone plug Sleeve (ground) O ST SUB IN jacks These are 1/4" phone jacks (unbalanced) for mixing the signal from an external device into the ST bus. Nominal input level is +4 dB. Pin wiring is as follows. Tip (send) 1/4" phone plug Sleeve (ground) P CUE SUB IN jacks These are 1/4" phone jacks (unbalanced) for mixing the signal from an external device into the PFL bus. Nominal input level is +4 dB. Pin wiring is as follows. Tip (send) 1/4" phone plug Sleeve (ground) Q PHANTOM MASTER switch This is the master switch for the +48V phantom power supply. R VCA EXTERNAL I/O connector This connector can be connected to an external device which has a VCA control function. This allows the VCA control functionality of the other device to which this connector is connected to be controlled from a single console. If the M3000 is to be the master for the VCA control, set the VCA MASTER/SLAVE switch (N) to the MASTER position. If the M3000 is to be the slave, set the VCA MASTER/SLAVE switch to the SLAVE position. Pin wiring is as follows. Pin# Assignment 1 VCA control 1 2 VCA control 2 3 VCA control 3 4 VCA control 4 5 VCA control 5 6 VCA control 6 7 VCA control 7 8 VC...
Эта инструкция также подходит к моделям:Музыкальные инструменты - M3000-24 (680.69 kb)