Оценок - , средний балл:
(
)
)
Производитель: Yamaha
Размер: 5.49 mb
Название файла:
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
К этому устройству также есть другие инструкции:
Фрагмент инструкции
If this switch is ON, the pre-fader signal is sent to the AUX bus, and will not be affected by the channel fader. NOTE · If necessary, the pre-fader signal sent to the AUX buses can be changed to the signal before the equalizer by changing an internal jumper. A fee will be charged for this modification. In this case, the signal will be sent to the AUX buses even if the input channel’s ON switch is turned off. For details, contact to your Yamaha dealer listed at the end of this manual. EPAN Control This control determines the stereo positioning of the monaural channel signal on the buses. Rotate the knob clockwise to pan the signal to the odd channels of the GROUP buses and the ST L bus, and counter-clockwise to pan the signal to the even channels of the GROUP buses and the ST R bus. FBAL Control Adjusts the left and right volume balance of stereo channels. The signal input to the INPUT L jack will be sent to the odd channels of the GROUP buses or to the ST L bus, and the signal input to the INPUT R jack will be sent to the even channels of the GROUP buses or to the ST R bus. GON Switch/Indicator When this switch is on, that channel will be enabled and the indicator will light. NOTE · Even if the ON switch is off, you can turn on the PFL switch (K) and monitor the signal before the channel fader via the MONITOR OUT jacks and the PHONES jack. HInput Meter Three LEDs indicate the input channel signal level after the equalizer. The “-20” LED will light if the input signal level reaches -20 dB, and the “0” LED will light at nominal level. The PEAK LED will light red when the input signal reaches 3 dB before clipping. IBus Assign Switches These switches determine the bus(es) to which each channel’s signal is sent. Turning a switch on will output the signal to the corresponding bus. • 1-2, 3-4, 5-6, 7-8 switches: Assign the channel’s signal to the GROUP 1/2–7/8 buses. • ST switch: Assigns the channel’s signal to the Stereo L and R buses. • MONO switch: Assigns the channel’s signal to the MONO bus. NOTE · If you want the signal to be output to the corresponding bus(es), turn on the channel ON switch (G). JMUTE Switches (1–4) These assign the channel’s mute on/off to switches 1–4. If you turn on the MUTE master switches (1–4) (page 15) located in the MUTE MASTER section, the input channels whose corresponding MUTE switch is on will be muted. NOTE ·When a channel is muted, the ON indicator (G) will go dark. · Even if a channel is muted, you can turn on the PFL switch (K) and monitor the signal before the channel fader via the MONITOR OUT jacks and the PHONES jack. 10 Owner’s Manual Controls and Functions Controls and Functions NOTE ·When you turn on the PFL switch, the PFL indicator of the MONITOR section (page 18) will light. LChannel Fader Adjusts the output level of the input channel signal. Use these faders to adjust the balance between the various channels. NOTE ·To minimize noise, the faders of unused channels should be set to the lowest position. · The channel faders will affect the ST, MONO, GROUP 1– 8, and AUX 1–8 (when the PRE switch is off) buses. English Owner’s Manual 11 Controls and Functions 12 Owner’s Manual English Rear Panel Top Panel Master Control Section DC POWER INPUT REC OUT/USB Section (page 14) MONITOR Section (page 18) TALKBACK Section (page 15) STEREO MASTER Section (page 17) MATRIX OUT Section (page 14) 2TR IN/USB Section (page 13) MONO Section (page 19) AUX SEND Section (page 16) DC POWER INPUT Section (page 15) STEREO AUX RETURN Section (page 13) GROUP OUT Section (page 16) REC OUT/USB Section (page 14) MATRIX OUT Section (page 14) DC POWER INPUT Section (page 15) MUTE MASTER Section (page 15) TALKBACK Section (page 15) MONITOR Section (page 18) MONO Section (page 19) STEREO MASTER Section (page 17) 2TR IN/USB Section (page 13) STEREO MASTER Section (page 17) AUX SEND Section (page 16) GROUP OUT Section (page 16) English Controls and Functions Owner’s Manual 13 STEREO AUX RETURN Section 1 AUX RETURN Jacks These are unbalanced phone-jack type line inputs. Signals input from these jacks can be sent to the GROUP 1/ 2–7/8, ST L/R, MONO, and AUX 1–4 buses. To the MONO and AUX 1–4 buses, a mix of the L/MONO and R signal is sent. These jacks are typically used to receive the signal returned from an external effect device (reverb, delay, etc.). NOTE · These jacks can also be used as auxiliary stereo inputs. · If you connect to the L/MONO jack only, the mixer will recognize the signal as monaural and will send the identical signal to both the L/MONO and R jacks. 2 AUX Controls (1–4) These adjust the level at which the signals from the AUX RETURN jacks are sent (with L and R mixed) to the AUX 1–4 buses. The “Ў” position of the knob is nominal level (0 dB). 3 Bus Assign Switches These switches determine the bus(es) to which the signal is received from the AUX RETURN jacks. • 1-2, 3-4, 5-6, 7-8 switches: Send the signal to the GROUP 1/2–7/8 buses. • ST switch: Sends the signal to the ST L/R bus. • M...
Эта инструкция также подходит к моделям:Музыкальные инструменты - IM8-24 (5.49 mb)
Музыкальные инструменты - IM8-40 (5.49 mb)