Оценок - 2, средний балл: 3
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Refer to “About Redundant Networks” in the “About Connections” section (see page 13) for more information on redundant networks. NOTE • The use of Ethernet cables with Neutrik EtherCon CAT5e compatible RJ-45 plugs is recommended. Standard RJ45 plugs can also be used. • Use STP (shielded twisted pair) cable to prevent electromagnetic interference. Make sure that the metal parts of the plugs are electrically connected to the STP cable shield by conductive tape or comparable means. • Connect only Dante-compatible devices or GbE-compatible devices (including a computer). E[LINK/ACT] Indicators These indicators show the communication status of the [PRIMARY] and [SECONDARY] connectors. They flash fast if the Ethernet cables are connected properly. F[1G] Indicators These indicators light when the Dante network is functioning as Giga-bit Ethernet. GAC IN Connector Connect the supplied AC power cord here. First, connect the power cord to the device, then insert the power cord plug into the AC outlet. The supplied power cord features a special latching mechanism (V-LOCK) to prevent the power cord from being accidentally disconnected. Connect the power cord by inserting the power cord fully until it is locked. CAUTION: Be sure to turn the power off before connecting or disconnecting the power cord. Press the latch button on the plug to disconnect the power cord. H[FAN] Switch Sets the internal cooling fan to operate at either [HIGH] or [LOW] speed. This switch is set to [LOW] when the unit is initially shipped from the factory. As long as the unit is operated within the specified ambient temperature range either the [LOW] or [HIGH] setting can be used. The [HIGH] setting is recommended if the ambient temperature is high, if the unit is in direct sunlight even if the ambient temperature is within the specified operating range, and in any situation in which fan noise is not a problem. If two or more Rio units are mounted in the same rack and the fan speed is set to [LOW], leave a 1U rack space between every two units. Also either leave the open spaces uncovered or install appropriate ventilating panels to minimize the possibility of heat buildup. If three or more Rio units are mounted without space in the same rack, set the fan speeds to [HIGH]. D E F G H About Connections Owner’s Manual 13 About Connections There are two ways to connect the Rio to a Dante network. Daisy Chain Network A daisy chain is a wiring scheme in which multiple devices are connected together in sequence. In this way, networking is simple and requires no network switches. This connection method is suitable for a simple system with a small number of devices. However, if a large number of devices are connected, the latency value must be increased. Also, if a connection is broken in a daisy chain network, the signal flow is interrupted at that point and no signal will be transferred beyond that point. Star Network In a star network, each device is connected to a central network switch. Using a GbE-compatible network switch enables you to configure a wide-band, large-scale network. We recommend a network switch that features various functions to control and monitor the network (such as Qos, the ability to assign priority to data flows - e.g., clock synchronization or audio transmission on certain data circuits.) With this topology, it is common to configure a redundant network so that an unexpected network problem will not affect any audio or otherwise stable communications. About Redundant Networks A redundant network consists of two circuits, a primary circuit and a secondary circuit. Normally, the network operates on the primary circuit. However, if the primary connection is broken, the secondary circuit will automatically take over communications. Therefore, using a redundant network with a star topology would increase communication stability relative to a daisy chain network. 0123456789ABCDEF 0123456789ABCDEF 01234 EF 01234 EF 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 ON CL5 Rio3224-D (ID#1) Rio3224-D (ID#2) SECONDARY PRIMARY PRIMARY Rio3224-D (ID#1) 0123456789ABCDEF Rio3224-D (ID#2) 0123456789ABCDEF 1 2 3 4 5 6 7 8 ON CL5 01234 EF 01234 EF Computer Network switch A Network switch B Primary Dante Secondary Dante About Connections About Connections Dante Controller is a software application that allows configuration and audio routing of Dante networks. Use this application if you plan to connect or set up Dante-enabled devices that do not feature Rio-native support. Please download the Dante Controller application from the website listed below. Please note that Dante Controller Version 3.2.1 or later supports Rio. To run Dante Controller, a computer must feature a GbE-compatible Ethernet connector. Refer to the Dante Controller owner’s manual for details on Dante Controller. In Dante Controller, make the following basic settings: • [Network View] > [Routing] > I/O patching • [Network View] > [Clock Status] > Word clock mast...
Эта инструкция также подходит к моделям:Музыкальные инструменты - CL1 (3.55 mb)
Музыкальные инструменты - CL3 (3.55 mb)
Музыкальные инструменты - CL5 (3.55 mb)
Музыкальные инструменты - Rio3224-D (3.55 mb)