Оценок - 2, средний балл: 3
(
)
)
|
Фото и характеристики Yamaha YIT-W12 |
Фрагмент инструкции
(Lights up green) wireless connection established NOTE • The transmitter automatically stops if your Yamaha product is turned off or if an input source other than the transmitter is selected. To play back the PC audio again, disconnect the transmitter from the PC and then reconnect them. • If PC audio is not available on your Yamaha product, the transmitter may not be selected as the audio playback device on your PC. Check the audio device settings on your PC. For details, refer to the manuals of the PC. • Do not use a USB hub when connecting the transmitter to a PC. • You cannot play back PC audio on your Yamaha product when an iPod is connected to the transmitter. HINT • Your Yamaha product automatically turns on if you start playback on your PC. • Some Yamaha products will terminate the wireless connection and turn off automatically if a certain period of time elapses after PC playback is stopped. • You can enjoy videos on the PC monitor. Updating the firmware of the transmitter New firmware that provides additional features or product improvements will be released as needed. Updates can be downloaded from our website. Please check our website regularly for Information. En 7 Troubleshooting Refer to the table below when the unit does not function properly. If the problem you are experiencing is not listed below or if the instructions below do not help, contact the nearest authorized Yamaha dealer or service center. First, check the following: 1 The power cable of your Yamaha product is connected to an AC wall outlet securely. 2 The latest firmware is installed on the transmitter or your iPod. Problem/Cause Remedy A wireless connection cannot be made. (The green indicator is off.) Your iPod is not connected to the transmitter firmly. Reconnect the iPod to the transmitter. The battery of your iPod is low or run out. Charge the iPod (p.5). The supplied USB cable is not connected to the transmitter (or PC) firmly. Reconnect the USB cable. The USB driver software is not installed on your PC because the PC (operating system) is not supported by the transmitter. Use a PC (operating system) supported by the transmitter (p.10). A wireless connection cannot be made. (The green indicator flashes.) The group IDs of the transmitter and your Yamaha product are not same. Set both the products to the same group (p.3). iPod recognition has failed because your iPod is not supported by the transmitter. (In this case, the red indicator starts flashing 30 seconds after an iPod connection.) Use an iPod supported by the transmitter (p.10). If you are using a supported iPod, but still cannot establish a wireless connection, reconnect the iPod to the transmitter. If the problem happens frequently, disconnect the iPod from the transmitter, restart the iPod, and reconnect the iPod. 8 En There is a communication error between the transmitter and your iPod. (In this case, the red indicator starts flashing 30 seconds after an iPod connection.) Reconnect the iPod to the transmitter. If the problem happens frequently, disconnect the iPod from the transmitter, restart the iPod, and reconnect the iPod There is a device using 2.4-GHz band range (such as microwave ovens, cordless phones and Wi-Fi devices) nearby. Move those devices away from the transmitter and your Yamaha product, or turn off the power of the wireless devices. If you are using a wireless router, change the wireless channel to the highest one (e.g. 13 ch). No sound is coming from the Yamaha product although a wireless connection is established. The volume of your Yamaha product is too low. Turn up the volume. The mute function is activated on your Yamaha product. Cancel the mute function. An input source other than the transmitter (YIT) is selected on your Yamaha product. Select the transmitter (YIT) as the input source. Headphones are connected to your iPod. Disconnect the headphones from the iPod. The transmitter is not selected as the audio playback device on your PC. Check the audio device settings on your PC and select the transmitter as the audio playback device. (The name of the transmitter displayed on your PC varies depending on its operating system.) The sound is interrupted. (The green indicator flashes.) The transmitter is too far from your Yamaha product. Move the transmitter closer to your Yamaha product. The signal from the transmitter is blocked by your body, metallic objects or walls. Move the transmitter to another position so that the signal from the transmitter is not blocked. There is a device using 2.4-GHz band range (such as microwave ovens, cordless phones and Wi-Fi devices) nearby. Move those devices away from the transmitter and your Yamaha product, or turn off the power of the wireless devices. If you are using a wireless router, change the wireless channel to the highest one (e.g. 13 ch). En 9 No sound is coming from the Yamaha product when playing back music stored on an iPod. Your iPod is not connected to the transmitter firmly. Reconnect the ...