Оценок - 4, средний балл: 4
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
¦ Assembling the supplied cardboard microphone stand 3 Fit in 1 2 Remove Fit in Place horizontally Run through 45 Make sure that there are no obstacles between the IntelliBeam microphone and the walls in your listening room as these objects obstruct the path of sound beams. However, any objects that are in contact with the walls will be regarded as a protruding part of the walls. IntelliBeam microphone Upper limit CONNECTION/ INITIAL SETTINGS PLAYBACK SETTINGS TROUBLESHOOTING APPENDIX 2Check if a video pin cable is connected. Within 1 m (3.3 ft) Center height of this unit Cardboard microphone stand Within 1 m (3.3 ft) Listening position 1.8 m (6.0 ft) or more Lower limit Center line IntelliBeam microphone Cardboard microphone stand PREPARATION • “BEAM+SOUND OPTIMIZE” screen appears automatically when the IntelliBeam microphone is connected. “BEAM OPTIMIZE ONLY” or “SOUND OPTIMIZE ONLY” can be selected separately in setup menu (.p. 20). 2) y • Data set automatically can be saved in the system memory (.p. 22). You can save the several data depending on listening room and you can change the setting conveniently. 17 En Initial settings Using AUTO SETUP (IntelliBeam) 1Turn the unit and your TV on. 2Switch TV’s input to “VIDEO INPUT 1 (example)”. 3Connect the supplied IntelliBeam microphone to the INTELLIBEAM jack. •It is normal for loud test tones to be output during the AUTO SETUP procedure. Make sure that there are no children around in the listening room while the AUTO SETUP procedure is in progress. •Make sure that your listening room is as quiet as possible. For accurate measurement, turn off air conditioner or other devices that make noises. •If there are curtains in your listening room, we recommend following the procedure below. 1 Open the curtains to improve sound reflection. 2 Run “BEAM OPTIMIZE ONLY”. 3 Close the curtains. 4 Run “SOUND OPTIMIZE ONLY”. Notes IntelliBeam microphone 1) y When pressing RETURN key displays the setup menu Press SETUP key repeatedly and display the menu screen again, then select: “AUTO SETUP” .. “BEAM+SOUND OPTIMIZE”. When the screen is not displayed Confirm the case below. – The input jack of your TV and the video output jack of the unit are connected. – The input of your TV is set to “VIDEO INPUT 1 (example)”. 2) y “BEAM+SOUND OPTIMIZE” is selected automatically. When you perform “BEAM OPTIMIZE ONLY” or “SOUND OPTIMIZE ONLY” only, refer to “AUTO SETUP via setup menu (.p. 20)”. 3) y • Wait outside the room during the AUTO SETUP procedure. • The AUTO SETUP procedure takes about 3 minutes. • To cancel the AUTO SETUP procedure after it is started, press RETURN key. 18 En Initial settings The screen below is displayed after connecting IntelliBeam microphone to the unit. 1) 2) AUTO SETUP (PREPARATION & CHECK) Please connect the MIC. Please place the MIC at least 1.8m/6ft away from SoundPro- jector. The MIC should be set at ear level when seated. Measurement takes about 3min. After [ENTER] is pressed, please leave the room. [ENTER]:Start [RETURN]:Cancel The best setting may not be done if you are in the room. Prepare to leave the room in 10 seconds after pressing ENTER in step 4. Note 4 4 Press ENTER key to start the AUTO SETUP procedure and then leave the room within 10 seconds. 3) The setup screen automatically changes during the AUTO SETUP procedure. Will begin in 10 sec. Please leave the room. --------- AUTO SETUP START [RETURN]:Cancel (After 3 min.) MEASUREMENTCOMPLETE. BEAMMODE:5Beam/Plus2SUBWOOFER:Yes[ENTER]:Saveset-up. [RETURN]:Donotsaveset-up. SHOWRESULT If AUTO SETUP procedure is complete, this unit rings the chimes. 4) 5Press ENTER key to confirm the results. 5) The measurement result is saved. 6Remove the IntelliBeam microphone. AUTO SETUP COMPLETE Please remove the MIC from Sound Projector and the listening position. Initial screen appears. 6) Keep the IntelliBeam microphone in a safe place. The measurement results are stored in the internal memory of this unit until you run the AUTO SETUP procedure again or configure the settings manually. You can save the several measurement result using memory setting function (.p. 22). PREPARATION CONNECTION/ INITIAL SETTINGS PLAYBACK SETTINGS TROUBLESHOOTING APPENDIX 4) y • If an error occurs, an error buzzer sounds and an error message is displayed. For details on error messages, see “Error messages for AUTO SETUP” (.p. 21). • If “ENVIRONMENT CHECK:Failure” is displayed, refer to “Error messages for AUTO SETUP” (.p. 21), press RETURN key, and then run the AUTO SETUP procedure again. • Depending on the environment of your listening room, the beam angles of front right and left and surround left and right may be set to the same value even if “BEAM MODE :5 Beam” is displayed as a result. 5) y If you do not want to reflect the results, press RETURN key. 6) y When AUTO SETUP is performed from SETUP MENU, menu selection screen of SETUP MENU appears. 19 En Initial settings ¦ AUTO SETUP via setup menu 1Place the IntelliBeam microphone ...