Оценок - 5, средний балл: 4
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
For example, when you want to play a DVD, you would normally turn on the component, select DVD as the input source and press the play button to start playback. The TV macro feature lets you perform all of these operations simply by pressing the DVD macro button. Notes • The ways to set macros differ if your TV does not have the tuning capability. • If you press any control buttons on the remote control other than the ones used to set macros while setting macros, the setting procedure is automatically canceled. • If it takes more than 10 seconds in steps 2 and 3, the setting procedure is automatically canceled. In this case, repeat from step 1. TV POWER 21STEREO SLEEP CH LEVEL MENU RETURNTEST TV VOL VOLUME MUTE TV INPUT TV MUTE ENTER SURROUND OFF CODE SET SPORTS AV POWER STANDBY/ON 34567890+105BEAM ST+3BEAM 3BEAM TARGET MUSIC MOVIE VOL MODE INPUTMODE MACRO INPUT2INPUT1 TVSTBVCRDVD AUX YSP CINEMA DSP CH TV ¦ Setting macros for the TV with the tuning capability 1 Press and hold CODE SET on the remote control and then press one of the input selector buttons to select the input source you want to set macros for. Proceed to step 2 while holding down CODE SET. TV MUTE TVSTBVCRDVD AUX CODE SET 2 Press MACRO on the remote control while holding down CODE SET. TV MUTE MACRO CODE SET 3 Press CH +/– or the numeric buttons to select the TV channel. Check that the TV screen changes to the tuner screen. 5BEAM ST+3BEAM 3BEAM CH STEREO TARGET or 213 456 MUSIC MOVIE VOL MODE 89+10 7 SPORTS OFF 0 CINEMA DSP 4 Press TV INPUT on the remote control repeatedly so that the screen changes to the display of the input source selected in step 1. TV INPUT 5 Press ENTER on the remote control to confirm the macro setting. ENTER REMOTE CONTROL FEATURES ¦ Setting macros for the TV without the ¦ Operating macros tuning capability 1 Press and hold one of the input selector 1 Press and hold CODE SET on the remote buttons for approximately 2 seconds to control and then press one of the input select the input source you want to operate selector buttons to select the input source macros for. you want to set macros for. The TV input changes at the same time the input Proceed to step 2 while holding down CODE SET. mode changes. TVSTBVCRDVD AUX TV MUTE CODE SET TVSTBVCRDVD AUX ¦ Canceling the macros 2 Press MACRO on the remote control while holding down CODE SET. 1 Press and hold CODE SET on the remote control and then press one of the input TV MUTE MACRO selector buttons to select the input source you want to cancel the macros for. CODE SET Proceed to step 2 while holding down CODE SET. 3 Press INPUT1 on the remote control. TV MUTE TVSTBVCRDVD INPUT1 CODE SET AUX 4 Press CH +/– or TV INPUT on the remote control repeatedly so that the screen changes to the display of the input source selected in step 1. CH TV INPUT or 5 Press ENTER on the remote control to confirm the setting. ENTER 2 Press MACRO on the remote control while holding down CODE SET. TV MUTE MACRO CODE SET 3 Press ENTER on the remote control to cancel the macros. ENTER ADVANCED OPERATION English 91 TROUBLESHOOTING TROUBLESHOOTING ¦ General Problem Cause Remedy See page This unit fails to turn on when STANDBY/ON is pressed, or enters the standby mode soon after the power has been turned on. The power supply cable is not firmly connected to the AC wall outlet or to the AC inlet on the rear panel of this unit. Connect the power supply cable firmly to the AC wall outlet or to the AC inlet on the rear panel of this unit. 23 This unit has been exposed to a strong external electric shock (such as lightning and strong static electricity). Set this unit to the standby mode, disconnect the power supply cable, plug it back in after 30 seconds, then use it normally. — This unit suddenly enters the standby mode. The internal temperature becomes too high and the overheat protection circuitry has been activated. Wait about 1 hour for this unit to cool down and then turn it back on. — The sleep timer has turned the unit off. Turn on the power, and play the source again. — No sound. Incorrect input or output cable connections. Connect the cables properly. If the problem persists, the cables may be defective. 15 No appropriate input source has been selected. Select an appropriate input source with INPUT or the input selector buttons. 39 The volume is turned down. Turn up the volume. 40 The sound is muted. Press MUTE or VOLUME +/– on the remote control to resume audio output and then adjust the volume level. 41 Signals this unit cannot reproduce (such as PCM signals with more than 96 kHz of sampling frequency) are being received from source component. Play a source whose signals can be reproduced by this unit. — Change the system settings of the source component. — The sound suddenly goes off. The sleep timer has turned the unit off. Turn on the power, and play the source again. — The sound is muted. Press MUTE or VOLUME +/– on the remote control to resume audio output and then adjust the volume level. 41...