Оценок - 5, средний балл: 3.6
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
* To assemble the unit, make sure you have the following three packages: - RS70 (Rack System) - DTP4K2STD (Pad Set) - DTXP4 (Trigger Module) Before assembling the unit, lay a drum mat (sold separately). Before assembling the unit, lay a drum mat on the fl oor. Alternately, to prevent damaging your fl oor, lay the cardboard of the included packages, etc. on the fl oor before assembling the two parts shown in the circles in Figure 1. Figure 1: Unit Regular Assembly q DTXP4 (Drum Trigger Module) w TP65S (3-zone Drum Pad) e AC Adaptor r HH65 (Hi-Hat Controller) t PCY135 (3-zone Cymbal Pad) y TP65 (Drum Pad) u KP65 (Kick Pad) i RS70 (Rack System) Checking the contents of RS70 Open the RS70 (Rack System) package and confi rm the contents. Figure 2: RS70 (Rack System) RS70 (1) Cable Band (10) *1 Assembly Manual (1) *2 - RS70 *1 Use cable bands to bind cables to pipes in “ Connecting to a power source”. (Spare bands are included.) *2 Not this manual. Assembling the Rack System 1 Take out the rack system from the package and remove all the cushioning. Remove the bubble wrap on the pipes while assembling the rack system. The pipe ends may injure your fi ngers. Figure 3: Rack Assembly-1 * YAMAHA logo printed on pipe is facing the opposite side. 2 See Figure 3. Set up the rack system, with the YAMAHA logo label (a) on pipe facing the opposite side from you. Support the rack system with your right hand, and loosen the two knobs (b) and (c) on your left. Figure 4: Rack Assembly-2 A B 3 See Figure 4. Move the leg on your left (pipe ) in a clockwise direction until it is about 90 degrees from the pipe with the YAMAHA logo. Tighten the two knobs loosened in step 2 and fi x the position of pipe . 4 See Figure 3 again. Loosen the two knobs (d) and (e) on your right. 5 See Figure 4 again. Move the leg on your right (pipe ) in a counterclockwise direction until it is parallel with pipe . Tighten the two knobs loosened in step 4 and fi x the position of pipe . * In the following steps, loosen the knobs fi rst, decide the position of the pipe, and then tighten the knobs. Be careful not to tighten the knobs excessively. For better performance, make minor adjustments for each part of the unit with the knobs after the assembly is completed. Figure 5: Rack Assembly-3 J K L E G F H D C 6 See Figure 5. Loosen the two knobs ((f) on the upper left) aligned at the base of pipe , and move pipe slightly outward in a clockwise direction. Tighten the two knobs loosened and fi x the position of pipe . 7 Loosen the two knobs ((g) on the middle right) aligned at the base of pipe . Move pipe in a counterclockwise direction until it is about 90 degrees from the pipe with the YAMAHA logo. Tighten the two knobs loosened and fi x the position of pipe . 8 Loosen the knobs (h) and (j) (shown with on the opposite side of pipe ) of the cymbal holders and on the right and left and pull up the cymbal holders vertically to the height illustrated. Tighten the knobs loosened and fi x the positions of the cymbal holders. 9 Loosen the two knobs ((k) on the middle left) aligned at the base of pipe and the knob ((m) on the lower left) on the slim pipe supporting pipe . Move pipe all the way around the vertical pipe in a counterclockwise direction until it is about 90 degrees from the pipe with the YAMAHA logo. Tighten the three knobs loosened and fi x the position of pipe and the slim pipe supporting it. Be sure to move pipe in a counterclockwise direction. If you move it in a clockwise direction, the slim pipes may collide and bend. 10 Check that the entire rack system is stable. Hold the upper area of the vertical pipe and , and shake them. If the rack system is unstable, retighten the knobs tightened in steps 2 to 5. PRECAUTIONS Before using, please read this assembly manual, and use this product in a safe and proper manner. Particularly in the case of children and young users, parents or an instructor should teach the children the proper manner in which to use the device. WARNING If this symbol is ignored and the equipment is used improperly, fatal injury to persons or serious damage could occur. Do not let small children assemble or set up this product by themselves, or they may be injured. Always assemble this product with adult supervision. Be careful with the edges of the cymbal holders and the tom holders. The sharp holder ends may result in injury. Be careful with the edges of the spurs attached to the base. The sharp spur ends may result in injury. If this product is used with the rack system or a cymbal stand, make sure all bolts are tightened firmly. Also, when adjusting the height or angle, do not suddenly loosen the bolts. Loose bolts may result in the rack overturning or parts dropping, causing injury. Always set the product on a flat and solid surface. Placement on a sloping, unstable surface or on steps may result in the product being unstable and subject to overturning. When setting the product, please pay close attention to the handling and se...