Оценок - 1, средний балл: 5
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Also pay close attention so as not to let the water and detergent come into contact with the cushions used in the product; doing so may result in deterioration. Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums may drop, causing injury. Continued on the next page (on the back side) Mounting the pads and the trigger module on the rack system Mount the pads and the trigger module on the rack system. Then position the kick pad and the hi-hat. Mounting the TP65 (Drum pads) and TP100 (3-zone Drum pad) on the rack system Figure 10: Pads Assembly-1 Figure 11: TP65 and TP100 !1 TP100 !2 TP65 (Rear side) !3 TP100 (Rear side) !4 Clamp bolt 1 See Figure 11. Attach the clamp bolts (!4) on TP65s (!2) and TP100 (!3). Tighten the clamp bolts fi ve to six turns each. Figure 12: Pads Assembly-2 2 See Figure 12. Loosen the knobs of the tom holders and at the center of the rack system (shown with ). Move the tom holders as shown in Figure 12-(a). Then tighten the knobs and fi x the position of the tom holders and . 3 Loosen the knob of the tom holder on the right (shown with ). Move the tom holder inward as shown in Figure 12-(b). Tighten the knobs and attach the tom holder fi rmly at a position where it points slightly downward. Figure 13: Tom Holder and Drum Pad !5 Tom holder !6 Clamp bolt 4 Attach the TP65 (Drum pad) to the tom holder as shown in Figure 13. Tighten the clamp bolt and attach the drum pad TP65 fi rmly. 5 See Figure 12 again. Repeat step 3 and 4 in the same manner for tom holder at the center of the rack system and for tom holder on the right, and attach the TP65 (Drum pad) to each tom holder. 6 Loosen the knobs of the snare holder on the left (shown with ). Turn the snare holder as shown with the big arrow in Figure 12-(c) and set it up vertically. Turn the metal stick on the upper part of as shown with the small arrow in Figure 12-(c) until it is pointing slightly outward than pipe . 7 Attach the 3-zone drum pad TP100 to the snare holder set up in step 6. Tighten the clamp bolt and attach the 3-zone drum pad TP100 fi rmly. Mounting the PCY135 and PCY155 (Cymbal pads) on the rack system Figure 14: Pads Assembly-3 Figure 15: Cymbal holder-1 @1 PCY155 @2 Cymbal holder @3 Wing nut @4 Felt washer 1 See Figure 15. Remove the wing nut (@3) and the two felt washers (@4) from the cymbal holder (@2). Then turn the black plastic part in a counterclockwise direction and remove it. Figure 16: Cymbal holder-2 Figure 17: Cymbal holder-3 @5 Stopper @6 Drum key @7 Key bolt 2 See Figure 16. Attach the stopper to the cymbal holder, and fi x at a position where the L-shaped part of the stopper is on the opposite side from you. To fi x the position of the stopper (@5), use the drum key (@6) and tighten the key bolt (@7) fi rmly. 3 See Figure 17. Attach the black plastic part removed in step 1 to the cymbal holder, and tighten it in a clockwise direction. 4 Attach one of the felt washers removed in step 1 to the cymbal holder. The other felt washer will not be used within the standard assembly described in this manual. Figure 18: Cymbal holder and Cymbal pad 5 See Figure 18. Insert the end of the L-shaped part of the stopper into the oval-shaped hole on the cymbal pad (shown with ) to set the cymbal pad on the cymbal holder. * Cymbal pad PCY135 is very similar to Real High-Hat Pad RHH135. Check the part number on the reverse side. 6 Attach the included round-shaped felt with a large hole-diameter to the cymbal holder, then attach the wing nut removed in step 1 and tighten it. Turn the wing nut until you are certain that the cymbal pad is attached. The cymbal pad is designed to shake when you hit the surface, even when the wing nut is tightened securely. Mounting the DTXP4 (Trigger module) Figure 19: Pads Assembly-4 Figure 20: Module stand @8 Wing nut @9 Module stand #0 DTXP4 (Rear side) 1 Attach the module stand (@9) onto the rear side of the DTXP4 (#0) using the wing nuts (@8). Figure 21: Module stand and clamp #1 DTXP4 + Module stand #2 Clamp #3 Knob 2 Attach the module stand (#1) onto the clamp (#2). Tighten the knob (#3) and fi x the position. Assembling the KP65 (Kick pad) 1 If a drum mat (sold separately) is not available, lay a cardboard on the fl oor to prevent scratching the surface. Figure 22: KP65 Assembly #4 Body #5 Base #6 Wing bolt #7 Spring washer #8 Washer 2 Remove the wing bolt (#6), the spring washer (#7) and the washer (#8) from the body (#4), and keep the four sets nearby in the order removed. * If the wing bolt, the spring washer and/or the washer are separated from each other, set them as illustrated in Figure 22-(a). 3 Set the base (#5) on the body (#4), and attach them using the wing bolt, the spring washer and the washer removed in step 2. Assembling the HS650A (Hi-Hat stand) 1 If a drum mat (sold separately) is not available, lay a cardboard on the fl oor to prevent scratching the surface. Figure 23: HS650A Assembly $1 Radius rod $2 Hi-Hat clutch $3 Felt washer $4...