Оценок - 5, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
Use of any other adaptor may result in damage, malfunction or electric shock. Also, if you are not going to be using it for an extended period of time, disconnect the AC adaptor from the AC outlet. 2. CHECK Indicator This indicator shows whether an effect is ON/OFF, and also doubles as the Battery Check indicator. The indicator lights when an effect is ON. If this indicator goesdim or no longer lights while an effect is ON, the battery is near exhaustion and should be replaced immediately. 3. OUTPUT Jack The output jack is used to connect the unit to an amplifier or another device. 4. Pedal Switch This switch turns the effects ON/OFF. 5. Thumbscrew This thumbscrew is loosened to open the pedal, allowing battery replacement. For instructions on how to replace the battery, please refer to "CHANGING THE BATTERY (p.12)." 6. INPUT Jack This jack accepts input signals (coming from a guitar, some other musical instrument, or another effects unit). * The INPUT jack also serves as the power switch. Power is turned on whenever a plug is inserted into the INPUTjack, and is turned off when the plug is disconnected. When not using the unit, you should disconnect any cord connected to the INPUT jack. 7 RATE Knob WAVE Knob DEPTH Knob RATE Knob This adjusts the rate of the tremolo. The further you move the knob clockwise, the faster the rate becomes. DEPTH Knob This adjusts the depth of the tremolo. When it is turned fully counterclockwise, no tremolo effect will be created. WAVE Knob This controls the waveform of the tremolo. You can go from smooth volume changes to more dramatic ones. 8 MAKING THE CONNECTIONS * Inserting a plug into the INPUT Jack will automatically switch the unit on. * To prevent malfunction and/or damage to speakers or other devices; always turn down the volume, and turn off the power on all devices before making any connections. * If there are batteries in the unit while an AC adaptor is being used, normal operation will continue should the line voltage be interrupted (power blackout or power cord disconnection). * Once the connections have been completed, turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices. When powering up: Turn on the power to your guitar amp last. When powering down: Turn off the power to your guitar amp first. * Always make sure to have the volume level turned down before switching on power. Even with the volume all the way down, you may still hear some sound when the power is switched on, but this is normal, and does not indicate a malfunction. * When operating on battery power only, the unit's indicator will become dim when battery power gets too low. Replace the battery as soon as possible. * The CHECK indicator shows whether the effect is being applied or not. It does not indicate whether the power to the device is on or not. OPERATING THE UNIT 5 1. When you have made the necessary connections, set the knobs as shown in the illustration. 2. Depress the pedal switch to turn the effect on. (Make sure the CHECK indicator lights.) 3. Adjust the rate of the tremolo using the RATE knob. 4. Adjust the depth of the tremolo using the DEPTH knob. 5. Adjust the waveform of the tremolo using the WAVE knob. II CHANGING THE BATTERY When the indicator goes dim or no longer lights while an effect is on, it means that the battery is nearly dead and must be replaced. Replace the battery following the steps Pedal 1 Loosen the thumbscrew at the front of the pedal, then lift the pedal upwards to open the unit. * The thumbscrew can be left in the pedal while changing the battery. 2 Remove the old battery from the battery housing, and remove the snap cord connected to it. 3 Connect the snap cord to the new battery, and place the battery inside the battery housing. * Be sure to carefully observe the battery's polarity (+ versus -). 4 SI ip the coil springonto the spring base on the back of the pedal, then close the pedal. * Carefully avoid getting the snap cord caught in the coil spring. Finally, insert the thumbscrew into the guide bush hole and fasten it securely. SETTING EXAMPLES Vintage Tremolo Electric Piano sound Switching technique sound Rotary Speaker sound SPECIFICATIONS TR-2: Tremolo Nominal Input Level........-20 dBu Input Impedance..............1 M Nominal Output Level.....-20 dBu Output Impedance...........1 k LFO Rate..........................90 to 900 ms Residual Noise Level........-90 dBu (IHF-A Weighted, Typ.) Controls...........................Pedal Switch, RATE Knob, DEPTH Knob, WAVE Knob Indicator..........................CHECK Indicator (Serves also as battery check indicator) Connectors......................INPUT Jack, OUTPUT Jack, AC Adaptor Jack (DC 9 V) Power Supply...................DC 9 V: Dry Battery (6F22/ 9 V) AC Adaptor (PSA Series: Optional) Current Draw......................