Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
(i 0 о w v............................'’{I—!) !l . 1 ► ! I) MIDI OUT MIDI IN Sound module (e.g., Sound Canvas) ( a « шпР) СШШПЗ) ( ОМ ДЕД) OUTPUT L. R Stereo system О о © © • D • О о о • О • О SO LINE IN, AUX, TAPE IN • When using this unit with a MIDI keyboard ( 1 гЪ) ( IÏI ► 1 1 = 1 I) rrrrSTTSrrn II.......................................... Í) О Г (Я) 0) ^ 4.......■''(CU; MIDI OUT I MIDI IN Stereo system aCD| ocnl ■■it’ H№> MIDI keyboard О © >o О © OUTPUT L, R LINE IN, AUX, TAPE IN Connecting the AC adaptor To AC outlet Connect the included AC adaptor to the Sound Brush, and then plug it into an AC 3 outlet. By looping the AC adaptor cable around the cable hook, you can prevent the plug from accidentally being disconnected. Note " Use only the included AC adaptor. Using other AC adaptors can result in damage or malfunction. ■=i>The power will be on when you connect the AC adaptor. 8 ICONNECTIONS AND POWER Installing the Sound Brush in a rack Install the Sound Brush into the RAD-50 Rack Mount Adaptor (sold separately) as shown ¡11 the following illustration. Other half-rack size devices, such as the Sound Canvas, can also be installed. © Using a screwdriver, carefully remove the four rubber feet from the bottom of the unit. © Attach the RAD-50 adaptor to the Sound Brush using the screw holes located nearest the front of the unit, using the screws from the rubber feet. Do not re-attach the rubber feet. * When re-attaching the rubber feet to the unit, be sure to use the same screws that you used to attach the unit to the rack mount. Use of a different type of screw could result in damage or malfunction. □ Turn the power on Before you turn the power on, check the following points: Is the Sound Brush correctly connected to the other devices? Is the volume of the amp or sound system turned down? Turn the power of each device on. The STANDBY indicator will go out and the display will be as shown in the following illustration. The Sound Brush is now ready to play. POWER (TZJ°> STANDBY-J Roland "V somBrush DISK o TEMPO_RNO CLEAR :mm Q==üL—i) PAUSE REC SINGLE PEPT ( © 0 [=)[=]) STOP Play new ff ( mnE] EjjDŒE] ) <=>The STANDBY indicator will be lit when the power is off. 9 a HOW TO USE THE REMOTE CONTROL Before using The remote control unit contains a lithium battery. An insulation sheet is inserted to keep the battery from discharging. You must remove this insulation sheet before using the remote control. Grasp the tab and pull the sheet out. How to use the remote control When using the remote control, do not exceed the specified range of operation (5 m). Always aim it towards the Remote Sensor on the front panel of the Sound Brush. The remote control can also be used to control the SC-55 (Sound Canvas MIDI sound module, sold separately). Range of operation □ o~" = o C Distance : 5 m Angle : 40 degrees (left/right) oo ® ® ® ® ® ® ® ® ® © ®0 ® ® © ® ® Each button on the remote control has the following function: ALL MUTE POWER OO PART @©@® LEVEL REVERB ® ® ® © "" SONG........TEMPO ' ®®@® STOP PLAY REW FF ® ® ® ® INST Roland REMOTE CONTROLLER POWER button: This button simultaneously controls the power for the Sound Brush and the Sound Canvas. Sound Canvas buttons: These buttons control various functions of the Sound Canvas sound module. Sound Brush buttons: These buttons duplicate the functions of the Sound Brush’s front panel buttons. Note ■ The remote control is able to transmit only one operation at a time. *The remote control may not operate even within the range of operation if there is an obstacle between it and the main unit. * Using the remote control near other equipment that uses remote control systems may result in operational errors. *The life of the lithium battery depends on the amount and conditions of use. If after a while the operational range of the remote control decreases, change the lithium battery. * If you will not be using the remote control for a long period of time, remove the lithium battery. 10 ■ HOW TO USE THE REMOTE CONTROL < Using the Sound Brush together with the Sound Canvas sound module > When you use the Sound Brush together with the Sound Canvas sound module, the remote control of the Sound Brush can turn the power to both units ON and OFF simultaneously. When you use the remote control with both units, be sure they are located within the range of operation. When you want to control only one of the units, turn off the remote control receiving switch of the unit that you do not want to control. *When using the remote control to operate both units, be sure that both units are ON or OFF. If only one unit is ON when you begin, one unit will always be ON while the other is OFF. • When you don’t want to use the remote control (remote control reception switch on/off) @0 © While holding | SETj, press | CLEAR . The display will read “on". (2) When you press l_REWj,...