Оценок - 4, средний балл: 4.3
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owner's manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference. As shipped, the RMP-3’s battery is not installed. Please read “Preparations—Loading the Battery” and follow the instructions to install the battery. Copyright © 2005 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. Panel Description 1. Mini Speaker For the metronome's beep sound only. If the OUTPUT jack is being used, no sound is output. 2. [METRONOME] Button Selects the metronome parameter. 3. [START/STOP] Button Starts and stops the metronome. 4. PHONES VOLUME Knob Adjusts the OUTPUT jack's volume. * The volume of the mini speaker is adjusted with CLICK VOLUME. 5. [COACH] Button Selects the Coach mode. 6. VALUE [+]/[-] Button Use these buttons to change the values of each parameter. To increase the value rapidly, hold down [+] and press [-]. To decrease the value rapidly, hold down [-] and press [+]. 7. BEAT Indicator Flashes along quarter notes. Red indicator flashes on accent beats. 8. Head 9. Sensor 10.Tuning Bolts Adjusts the head tension. - 1 - C5100025 1RCC Side Panel 1—2 —3—4—5 û ^ ' 1. Security Slot ( ß ) 2. MIX IN Jack For connecting an external audio source (CD, MD, etc.) for playing along. 3. OUTPUT Jack For headphones, amp, or audio system. * The RMP-3 outputs sounds in monaural. 4. AC Adaptor Jack Connect the AC adaptor (optional) here. 5. POWER Switch Turns the power on/off. Preparations Loading the Battery 1. Press down and slide off the lid of the battery compartment (located on the bottom of the unit). 2. Connect the snap cord to the battery, and place it inside the battery compartment. * Verify the battery's polarity (+ versus -). 3. Securely close the battery cover. * Do not let the snap cord get caught in the battery compartment lid. When to Change the Battery The Battery LOW indicator ( ) at the lower left of the display begins to flash when the battery power drops. Insufficient battery power lowers the volume level of the mini speaker and causes unstable operation. Replace the battery as soon as possible. Connecting the AC Adaptor A BOSS PSA series AC adaptor (sold separately) can be used to power the RMP-3. Turn off the power before connecting the AC adaptor. Use only the BOSS PSA-series AC adaptor. Other adaptors may cause malfunction or damage to the RMP-3 and must never be used. The Battery LOW indicator ( ) flashes when the battery power drops while the AC adaptor is used. Adjusting the Head Tension BEFORE playing the RMP-3, you must tune the head to your preferred playing tension. The head is NOT tuned before shipping. Always tighten the tuning bolts in the order shown in the figure. * Failure to adjust the tension may result in damage to the head. * Head tension may change with extended use. Make adjustments as needed. NOTE NOTE (MEMO) - 2 - About the Display Count Beat Battery LOW Indicator Flashes when the battery power drops. a LOW on cu Tempo/Value Rhythm Type Metronome Needle r Trigger Indicator Appears when the head is struck. Replacing the Head If the head has been damaged or no longer maintains correct tension, replace it. To order replacement heads (RMP-3 Mesh Head), contact the retailer from whom you purchased the unit or the nearest Roland Service Center. NOTE The MH-8 Mesh Head is not compatible and cannot be used. Replacing the Head When replacing or tuning, use the included tuning key. 1. Remove all tuning bolts. Gradually loosen each one in order, turning them counterclockwise. * Do not lose the tuning bolts. 2. Open the case, and then remove the old head. 3. Place the new head in the case. 4. Securely close the case. 5. Attach all eight tuning bolts. 6. Adjust the tension of the head. Refer to "Adjusting the Head Tension. Specifications Pad Size 8 inches Tempo 20-260 Beat 24 types Rhythm Types 18 types Metronome Sounds 5 Coach Mode Functions: 5 Exercise Variations: 20 Connectors PHONES/OUTPUT Jack: 1 (Stereo miniature phone type) MIX IN Jack: 1 (Miniature phone type) AC Adaptor Jack Power Supply DC 9 V: Dry Battery 6F22/1604 (9 V) type (carbon) Dry Battery 6LR61/1604A (9 V) type (alkaline) AC Adaptor Current Draw 55 mA * Expected battery life under continuous use: Carbon: 2 hours Alkaline: 6 hours These figures will vary depending on the actual conditions of use. Stand Screw Size M8 Dimensions 263 (W) x 348 (D) x 78 (H) mm 10-3/8 (W) x 13-3/4 (D) x 3-1/8 (H) inches Weight 1.2 kg / 2 lbs 11 oz (including a battery) Accessories Dry Battery 6F22/1604 (9 V) type (carbon) Tuning Key Owner's Manual Le...