Оценок - 2, средний балл: 4.5
(
)
)
|
Фото и характеристики Roland RD-300SX |
Фрагмент инструкции
By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices. Turning On the Power 1 Before you switch on the power, turn the volume down all the way using the VOLUME slider. Also completely turn down the volume of any connected audio device and other equipment. Press the [POWER] switch on the back of the unit. The power will turn on, and “Pno” appears in the display. To prevent incorrect functioning of the Pitch Bend Lever (p. 30), refrain from touching the lever when you turn on the power. This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally. Rear Panel Lower Position ON 3 Turn on the power to connected external devices. 4 Adjust the volume of the connected external device. 5 Adjust the RD-300SX’s volume to obtain the proper volume level. Getting Ready 2 Turn off the power to connected external devices. 3 Press the [Power] switch on the back of the unit. The power is switched off. Turning Off the Power Rear Panel Upper Position OFF Getting Ready 2 Turn off the power to connected external devices. 3 Press the [Power] switch on the back of the unit. The power is switched off. Turning Off the Power Rear Panel Upper Position OFF Adjusting the Volume 1 Adjust the volume using the VOLUME slider. Move the slider up to increase the volume, or down to lower it. Also adjust the volume of the connected device to an appropriate level. Getting Ready 1 Press [EDIT], getting the indicator to light. The Edit Menu screen appears. 2 Press [INC] or [DEC] to select “System,” then press [ENTER]. The TONE SELECT button blinks. 3 Press [PIANO]. The parameter name (tun) appears in the display while [PIANO] is held down. When the button is released, the last three digits of the currently set basic reference pitch are shown in the display. 4 Press [INC] or [DEC] to change the standard pitch. You can set the standard pitch anywhere in a range of 415.3 Hz to 466.2 Hz. The pitch is lowered 0.1 Hz each time [DEC] is pressed. When the button is held down, the pitch drops continuously. The pitch is raised 0.1 Hz each time [INC] is pressed. When the button is held down, the pitch rises continuously. To return to the original pitch, press [DEC] and [INC] simultaneously. 5 If you want to save the settings, press [WRITE]. A confirmation screen appears. 6 If you want to continue with the save, press [ENTER]. You can return to Step 2. Tuning to Other Instruments’ Pitches (Master Tune) 2,42,6 3 1 5 For faster value increases, keep [INC] pressed down and press [DEC]. For decreasing value faster, keep [DEC] pressed down and press [INC]. If this setting has not been saved, it is lost when the power is turned off. Getting Ready 1 Press [EDIT], getting the indicator to light. The Edit Menu screen appears. 2 Press [INC] or [DEC] to select “System,” then press [ENTER]. The TONE SELECT button blinks. 3 Press [PIANO]. The parameter name (tun) appears in the display while [PIANO] is held down. When the button is released, the last three digits of the currently set basic reference pitch are shown in the display. 4 Press [INC] or [DEC] to change the standard pitch. You can set the standard pitch anywhere in a range of 415.3 Hz to 466.2 Hz. The pitch is lowered 0.1 Hz each time [DEC] is pressed. When the button is held down, the pitch drops continuously. The pitch is raised 0.1 Hz each time [INC] is pressed. When the button is held down, the pitch rises continuously. To return to the original pitch, press [DEC] and [INC] simultaneously. 5 If you want to save the settings, press [WRITE]. A confirmation screen appears. 6 If you want to continue with the save, press [ENTER]. You can return to Step 2. Tuning to Other Instruments’ Pitches (Master Tune) 2,42,6 3 1 5 For faster value increases, keep [INC] pressed down and press [DEC]. For decreasing value faster, keep [DEC] pressed down and press [INC]. If this setting has not been saved, it is lost when the power is turned off. X Basic Organization of the RD-300SX Units of Sound The RD-300SX can be divided into two sections: a keyboard controller section and a sound generator section. The two sections are connected internally by means of MIDI. Keyboard Controller Section (controllers such as keyboard, pitch bend lever, etc.) Sound Generator Section Play Keyboard Controller Section This section includes the keyboard, the Pitch Bend/Modulation lever, the panel knobs, and any pedal connected to the rear panel. Actions such as pressing and releasing of keys on the keyboard, depressing a pedal, and so forth, are converted to MIDI messages and sent to the sound generator section, or to an external MIDI device. Sound Generator Section The sound generator section produces the sound. Here, MIDI messages received from the keyboard controller section or external MIDI device are converted to musical signals, which are then output as analog signals from the OUTPUT and PHONES jack...