Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
• With the PD-80R, make sure to use the supplied stereo cable when connecting it. Otherwise (if you use a monaural cable), you won’t be able to employ striking location detection, rim shot, and cross stick playing techniques. • Connect the L-shaped plug of the included cable to the PD-80/80R. This will prevent strain from being applied to the PD-80/80R. Correspondences Between Playing Techniques and Percussion Sound Modules Sound Module Trigger Input Rim Shot Cross Stick Positional Sensing TD-6V 2 (SNARE) o o – TD-8 3 (SNARE) o o o TD-10 2 (SNARE) o – o TD-10 (TDW-1) 2 (SNARE) o o o HPD-15 1, 2 o – – SPD-20 1, 2 o – – SPD-S 1, 2 o – – * Rim shots and cross-stick performances can be made only with the PD-80R. Connecting to the TD-5, TD-7 or SPD-11 • Use the included cable to make connections. • Connect the L-shaped plug of the included cable to the PD-80/80R. This will prevent strain from being applied to the PD-80/ 80R. • It is not possible to play rim shots even if you connect the PD-80R to the TD-5, TD-7, or SPD-11. 6 Next Replacing the Head When the Head Should Be Replaced The head is an expendable item that eventually will wear out and need to be replaced. Replace the head when the following occurs: • The head surface is torn • Striking points are no longer detected correctly, even when the head tension is properly adjusted. • Slack portions remain in the head even after the head tension is properly adjusted. Replacement heads (optional) MH-8 Mesh Head: for either PD-80 or PD-80R Replacing the Head 1. Remove all tuning bolts and washers. If using the PD-80R, press the lock bushing (in figure below) in place with your finger as you remove each tuning bolt, to prevent the bushings from being pulled off the frame. Tuning Key Hoop Hoop's Rubber Portion Lock Bushing Washer Frame Tuning Bolt For more on the lock bushings, refer to the following section, “About the PD-80R's Lock Bushings.” 2. Remove the hoop. 3. Remove the old head. 4. Place the new head on the frame. 5. Place the hoop onto the head. 6. Pass the tuning bolts through the washers, then attach them to the hoop and frame. 7. Next, adjust the tension of the head. Refer to “Adjusting the Head Tension” (p. 5). Do not firmly tighten a single tuning bolt by itself. Doing so will make it impossible to tension the head evenly, and will cause malfunctions such as failure to accurately detect the striking location. About the PD-80R's Lock Bushings The PD-80R is provided with lock bushings to prevent rotation and loosening of the tuning bolts caused by vibration transmitted from the hoop, as the result of using rim shots or other performance techniques. If a lock bushing happens to become separated from the frame while the head is being replaced, position the bushing so its four slots are aligned with the corresponding ridges in the frame, then press down firmly on the bushing. Lock Bushing Frame Specifications PD-80 (Pad) Pad Size: 8 inches Trigger: 1 (Head) Dimensions: 245 (W) x 310 (D) x 95 (H) mm 9-11/16 (W) x 12-1/4 (D) x 3-3/4 (H) inches Weight: 1.6 kg 3 lbs 8 oz Accessories: Owner’s Manual, Connection Cable, Tuning Key Options: Mesh Head (MH-8), Pad Mounts (MDH-7U, MDH-10), Drum Stands (MDS-3C, MDS-6, MDS-8C, MDS-10, MDS-20) PD-80R (Pad) Pad Size: 8 inches Triggers: 2 (Head, Rim) Dimensions: 245 (W) x 310 (D) x 95 (H) mm 9-11/16 (W) x 12-1/4 (W) x 3-3/4 (H) inches Weight: 1.7 kg 3 lbs 12 oz Accessories: Owner's Manual, Connection Cable, Tuning Key Options: Mesh Head (MH-8), Pad Mounts (MDH-7U, MDH-10), Drum Stands (MDS-3C, MDS-6, MDS-8C, MDS-10, MDS-20) In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice. 7 Information When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as shown below. EGYPT Al Fanny Trading Office 9, EBN Hagar A1 Askalany Street, AFRICA AFRICAAFRICA PHILIPPINES G.A. Yupangco & Co. Inc. 339 Gil J. Puyat Avenue Makati, Metro Manila 1200, PHILIPPINES TEL: (02) 899 9801 MEXICO Casa Veerkamp, s.a. de c.v. Av. Toluca No. 323, Col. Olivar de los Padres 01780 Mexico D.F. MEXICO TEL: (55) 5668-6699 IRELAND Roland Ireland G2 Calmount Park, Calmount Avenue, Dublin 12 Republic of IRELAND TEL: (01) 4294444 IRAN MOCO, INC. No.41 Nike St., Dr.Shariyati Ave., Roberoye Cerahe Mirdamad Tehran, IRAN TEL: (021) 285-4169 ARD E1 Golf, Heliopolis, Cairo 11341, EGYPT TEL: 20-2-417-1828 REUNION Maison FO - YAM Marcel 25 Rue Jules Hermann, Chaudron - BP79 97 491 Ste Clotilde Cedex, REUNION ISLAND TEL: (0262) 218-429 SINGAPORE Swee Lee Company 150 Sims Drive, SINGAPORE 387381 TEL: 6846-3676 CRISTOFORI MUSIC PTE LTD Blk 3014, Bedok Industrial Park E, #02-2148, SINGAPORE 489980 TEL: 6243-9555 PANAMA SUPRO MUNDIAL, S.A. Boulevard Andrews, Albrook, Panama City, REP. DE PANAMA TEL: 315-0101 PARAGUAY Distribuidora De Instrumentos Musicales J.E. Olear y ESQ. Manduvira ITALY Roland Italy S. p. A. Viale delle Industrie 8, ...