Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
To make sure you get the most out of the OS-2 OVERDRIVE/DISTORTION, and enjoy continuing satisfaction as a result of operating it under the best of conditions, please thoroughly read these instructions. • Overdrive and distortion have been combined into one compact effects unit. • You are provided with a wealth of new sound creation possibilities as a result of the mixture of overdriven and distorted sounds. • The unit is equipped with a Color knob which allows you to adjust at will the respective portions included in the sound mixture. 9 A overdrive that really sounds like it comes from a large-scale tube amp is created as a result of the unique BOSS "Asymmetrical Overdrive Circuitry'' that is incorporated in the unit. OS-2 Over Drive/ Distortion OUTPUT INPUT 4- Over Drive/ Distortion OS-2 -tas- [03 I The volume of that when effects are applied is reduced. When turned fully counterclockwise (O) no sound at all will be output. © Tone Knob Adjusts the tone of the effected sound. [03 : The sound becomes sharper, with more emphasis placed on the upper range. [Oj : The sound becomes softer, since the upper range is cut. © Output Jack This output jack is used for connecting with an amplifier or other effects devices. © Pedal Switch Used to turn effects on or off. © Thumb Screw When this screw is loosened, the pedal opens, allowing for the battery to be changed For information on how to change the battery, refer to "BATTERY REPLACEMENT' * The screw should not be removed completely from the pedal. If it should come uif. make sure you do not misplace it. © Color Knob Adjusts the balance between the overdrive and distortion. [03 '• The proportion of the distorted sound is increased. [03 I The proportion of the overdriven sound is increased. * When the knob is turned to one or the other extreme, you obtain solely either the distortion or the overdrive effect. © Drive Knob Adjusts the degree to which the overdrive/distortion will be applied. [03 • The distortion becomes greater, providing a truly heavy sound. [03 ^ The distortion is reduced. ®Input Jack This jack accepts connection of a guitar or other electronic instruments and devices. * The Input jack is equipped with a power switch When a plug is inserted'into it, the power is turned on; and when the plug is pulled out. the power is turned off. When the unit is not being used, any cord connected to the Input jack should be disconnected. HCONNECTIONS Connect to the AC adaptor jack cotoe 4- output input 4- Over Drive/ Distortion OS-2 AC Adaptor BOSS PSA series * When a plug is inserted into the Input jack, the power is turned on. — ■ OPERATION......................................................................................... © Once you have all cords connected, the knobs on the panel should be set as shown in the illustration. * Always make sure you turn down the volume on your amplifier before connecting or disconnecting any cords. 0 Depress the pedal switch thus turning the effect on. (The Check Indicator will light up.) Using the Color knob © adjust the balance between the distortion and the overdrive. When turned clockwise, the distorted sound proportion is increased. When turned counterclockwise, the overdriven sound proportion is increased. When the knob is turned to one or the other extreme, you obtain solely either the distortion or the overdrive effect. @ Using the Drive knob © adjust the degree to which the effect is to be applied. The further it is moved clockwise, the greater the distortion becomes. © Using the Tone knob ©. adjust the tone of the sound heard when the effect is on. The further it is moved clockwise, the more the upper range is enhanced, and the sharper the sound becomes. © Using the Level knob ©, adjust the volume of what is heard when the effect is on. It should be adjusted so there is no difference in volume between when the effect is on and when it is off. cM^ex LEVEL ‘ TONE * DRIVE COLOR LEVEL TONE DRIVE COLOR Si ■ BATTERY REPLACEMENT ■ IMPORTANT NOTES ©Loosen the thumb screw on the pedal to open it. ©Take out the battery from the battery housing and disconnect the battery snap. (DConnect a new battery to the battery snap,then replace the battery in to the battery housing. * Make sure that the polarity of the battery is correct. ©Push the coil spring into the spring base on the rear of the pedal,then close the pedal. * Make sure that the snap cord is not caught in the pedal or coil spring. ©Insert the thumb screw into the guide bush hole and firmly tighten the screw. Use one 9-volt battery •Do not subject the unit to temperature extremes (eg. direct sunlight in an enclosed vehicle). Avoid using or storing the unit in dusty or humid areas or areas that are subject to high vibration levels. • Remove the battery whenever the unit is not going to be used for an extended period of time. • When operating solely on a battery, the unit's indicator becomes dim when the...